ML610Q412P-NNNTB03A7 Rohm Semiconductor, ML610Q412P-NNNTB03A7 Datasheet - Page 379

• Manufacturer Part Number: ML610Q412P-NNNTB03A7
• Description: MCU 8BIT 16K FLASH 120-TQFP
• Manufacturer: Rohm Semiconductor

Specifications of ML610Q412P-NNNTB03A7

• Core Processor: nX-U8/100
• Core Size: 8-Bit
• Speed: 625kHz
• Connectivity: I²C, SSP, UART/USART
• Peripherals: LCD, POR, PWM, WDT
• Number Of I /o: 14
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.1 V ~ 3.6 V
• Data Converters: A/D 2x12b, 2x24b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Chapter 25 Successive Approximation type A/D converter
• Operating conditions
[ ] Please confirm the operating voltage and the clock frequency.
• Others
[ ] Use the A/D converter when the HSCLK is oscillating.
[ ] Do not set SARUN bit of SADCON1 register to “1” on the condition both SACH0 bit and SACH1 bit of SADMOD0
register are “0” (Refer to Section 25.2.7 ~ Section 25.2.8).
Chapter 26 LCD driver
• Bias
[ ] 1/3 bias
• Duty
[ ] 1/1 ~ 1/4 duty
• COM/SEG
[ ] ML610Q411/ML610Q415: 4COM x 36SEG
[ ] ML610Q412: 4COM x 44SEG
• External capacitor
[ ] Ca=1uF(connected to VL1 pin), [ ] Cb=1uF(connected to VL2 pin),
[ ] Cc=1uF(connected to VL3 pin),
[ ] C12=1uF（connected between C1 and C2 pin）
Chapter 27 BLD (Battery Low Detector)
• Changing the threshold
[ ] Please select the threshold voltage when the BLD circuit is OFF.
Chapter 28 Power circuit
• External capacitor
[ ] CL0=1uF （connected to VDDL pin）,
this.
Chapter 29 On-chip debug
[ ] Supply 3.0V ~ 3.6V to VDD pin when programming (erasing and writing) the Flash ROM with Oki semiconductor
development tool uEASE.
[ ] Please do not apply LSIs being used for debugging to mass production.
[ ] Please validate the ROM code on your production board without Oki semiconductor development tool uEASE.
Appendix A SFR (Specific Function Registers)
• Initial data
[ ] Please confirm there are some SFRs have undefined initial value at reset (Refer to Appendix A in the user’s manual).
Appendix C Electrical Characteristics
• Operating voltage vs Operating frequency
[ ] Please confirm the operating conditions.
V
[ ] +1.1V to +3.6V (0kHz to 36kHz: Low-speed crystal oscillation clock operation)
[ ] +1.3V to +3.6V (30kHz to 625kHz: Built-in RC oscillation clock operation)
DD
=1.3V~3.6V (HSCLK=375KHz~625KHz）, AV
[ ] Cx =0.1uF (connected to VDDX pin）/ ML610Q415 does not require
DD
=2.2V~3.6V
E – 4
ML610Q411/ML610Q412/ML610Q415 User’s Manual
Appendix E Check List