MT47H64M16HR-3 IT:H Micron Technology Inc, MT47H64M16HR-3 IT:H Datasheet - Page 120

• Manufacturer Part Number: MT47H64M16HR-3 IT:H
• Description: DRAM Chip DDR2 SDRAM 1G-Bit 64Mx16 1.8V 84-Pin FBGA Tray
• Manufacturer: Micron Technology Inc
• Type: DDR2 SDRAMr

Specifications of MT47H64M16HR-3 IT:H

• Density: 1 Gb
• Maximum Clock Rate: 667 MHz
• Package: 84FBGA
• Operating Supply Voltage: 1.8 V
• Maximum Random Access Time: 0.45 ns
• Operating Temperature: -40 to 85 °C
• Organization: 64Mx16
• Address Bus: 16b
• Access Time (max): 450ps
• Operating Supply Voltage (typ): 1.8V
• Package Type: FBGA
• Operating Temp Range: -40C to 85C
• Operating Supply Voltage (max): 1.9V
• Operating Supply Voltage (min): 1.7V
• Supply Current: 135mA
• Pin Count: 84
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Compliant

Table 44: Truth Table – CKE
Notes 1–4 apply to the entire table
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. V 6/10 EN
Current State
Bank(s) active
All banks idle
Power-down
Self refresh
Previous Cycle
Notes:
(n - 1)
H
H
H
H
L
L
L
L
10. Valid commands for self refresh exit are NOP and DESELECT only.
11. Power-down and self refresh can not be entered while READ or WRITE operations,
12. Minimum CKE high time is
13. Self refresh mode can only be entered from the all banks idle state.
14. Must be a legal command, as defined in Table 37 (page 71).
1. CKE (n) is the logic state of CKE at clock edge n; CKE (n - 1) was the state of CKE at the
2. Current state is the state of the DDR2 SDRAM immediately prior to clock edge n.
3. Command (n) is the command registered at clock edge n, and action (n) is a result of
4. The state of ODT does not affect the states described in this table. The ODT function is
5. Power-down modes do not perform any REFRESH operations. The duration of power-
6. “X” means “Don’t Care” (including floating around V
7. All states and sequences not shown are illegal or reserved unless explicitly described else-
8. Valid commands for power-down entry and exit are NOP and DESELECT only.
9. On self refresh exit, DESELECT or NOP commands must be issued on every clock edge
previous clock edge.
command (n).
not available during self refresh (see ODT Timing (page 128) for more details and specif-
ic restrictions).
down mode is therefore limited by the refresh requirements.
down. However, ODT must be driven high or low in power-down if the ODT function is
enabled via EMR.
where in this document.
occurring during the
(200 clocks) is satisfied.
LOAD MODE operations, or PRECHARGE operations are in progress. See SELF REFRESH
(page 116) and SELF REFRESH (page 77) for a list of detailed restrictions.
This requires a minimum of 3 clock cycles of registration.
CKE
Cycle (n)
Current
H
H
H
L
L
L
L
L
t
XSNR period. READ commands may be issued only after
CS#, RAS#, CAS#,
120
DESELECT or NOP
DESELECT or NOP
DESELECT or NOP Active power-down entry
DESELECT or NOP
Command (n)
t
CKE = 3 ×
Refresh
WE#
Shown in Table 37 (page 71)
X
X
Micron Technology, Inc. reserves the right to change products or specifications without notice.
t
CK. Minimum CKE LOW time is
1Gb: x4, x8, x16 DDR2 SDRAM
Precharge power-down
Maintain power-down
Maintain self refresh
Self refresh entry
Power-down exit
Self refresh exit
Action (n)
REF
entry
) in self refresh and power-
Power-Down Mode
© 2004 Micron Technology, Inc. All rights reserved.
t
CKE = 3 ×
7, 8, 11, 12
10, 12, 13
7, 9, 10
7, 8, 11
Notes
t
5, 6
7, 8
14
XSRD
6
t
CK.