1893AFLF IDT, 1893AFLF Datasheet - Page 36

• Manufacturer Part Number: 1893AFLF
• Description: Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
• Manufacturer: IDT
• Type: Integrated PHY Transceiverr

Specifications of 1893AFLF

• Rohs: yes
• Product: Ethernet Transceivers
• Data Rate: 10 Mb/s, 100 Mb/s
• Supply Voltage - Max: 3.47 V
• Supply Voltage - Min: 3.14 V
• Maximum Operating Temperature: + 70 C
• Package / Case: SSOP-48
• Ethernet Connection Type: 100Base-TX, 10Base-T
• Maximum Supply Current: 160 mA
• Minimum Operating Temperature: 0 C
• Standard Supported: 802.3
• Part # Aliases: ICS1893AFLF

7.2.1 Auto-Negotiation General Process
ICS1893AF, Rev D 10/26/04
The Auto-Negotiation sublayer uses a physical signaling technique that is transparent at the packet level
and all higher protocol levels. This technique builds on the link pulse mechanism employed in 10Base-T
operations and is fully compliant with clause 28 of the ISO/IEC 8802-3 standard.
During the auto-negotiation process, both the ICS1893AF and its remote link partner use Fast Link Pulses
(FLPs) to simultaneously ‘advertise’ (that is, exchange) information on their respective technology
capabilities as follows:
1. For the auto-negotiation process to take place, both the ICS1893AF and its remote link partner must
2. The ICS1893AF obtains the data for its FLP bursts from the Auto-Negotiation Advertisement Register
3. Both the ICS1893AF and the remote link partner substitute Fast Link Pulse (FLP) bursts in place of the
4. Similarly, the ICS1893AF places the Auto-Negotiation data received from its remote link partner's FLP
5. After the ICS1893AF and its remote link partner exchange technology capability information, the
6. To indicate that the auto-negotiation process is complete, the ICS1893AF sets bits 1.5 and 17.4 high to
first both support and be enabled for Auto-Negotiation.
(Register 4).
Normal Link Pulses (NLPs). In each FLP burst, the ICS1893AF transmits information on its technology
capability through its Link Control Word, which includes link configuration and status data.
bursts into the Auto-Negotiation Link Partner Ability Register (Register 5).
ICS1893AF Auto-Negotiation sublayer contrasts the data in Registers 4 and 5 and automatically
selects for the operating mode the highest-priority technology that both Register 4 and 5 have in
common. (That is, both the ICS1893AF and its remote link partner use a predetermined priority list for
selecting the operating mode, thereby ensuring that both sides of the link make the same selection.) As
follows from Annex 28B of the ISO/IEC 8802-3 standard, the pre-determined technology priorities are
listed from 1 (highest priority) to 5 (lowest priority):
(1) 100Base-TX full duplex
(2) 100Base-T4. (The ICS1893AF does not support this technology.)
(3) 100Base-TX (half duplex)
(4) 10Base-T full duplex
(5) 10Base-T (half duplex)
Table 7-1
place.
Table 7-1. Example of Selection Process of Highest-Priority Technology
logic one. After successful completion of the auto-negotiation process, the ICS1893AF
Auto-Negotiation sublayer performs the following steps:
a. It sets to logic one the Status Register’s Auto-Negotiation Complete bit (bit 1.5, which is also
b. It enables the negotiated link technology (such as the 100Base Transmit modules and 100Base
c. It disables the unused technologies to reduce the overall power consumption.
ICS1893AF Data Sheet - Release
If Register 4 Has These
Technologies:
(3) 100Base-TX half duplex
(4) 100Base-T full duplex
available in the QuickPoll register as bit 17.4).
Receive modules).
shows an example of how the selection process of the highest-priority technology takes
Copyright © 2004, Integrated Circuit Systems, Inc.
If Register 5 Has These
Technologies:
(1) 100Base-TX full duplex
(3) 100Base-TX half duplex
All rights reserved.
36
Resulting Highest-Priority Common
Technology from Auto-Negotiation
Sublayer
(3) 100Base-TX half duplex
Chapter 7 Functional Blocks
October, 2004