1893AFLF IDT, 1893AFLF Datasheet - Page 93

• Manufacturer Part Number: 1893AFLF
• Description: Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
• Manufacturer: IDT
• Type: Integrated PHY Transceiverr

Specifications of 1893AFLF

• Rohs: yes
• Product: Ethernet Transceivers
• Data Rate: 10 Mb/s, 100 Mb/s
• Supply Voltage - Max: 3.47 V
• Supply Voltage - Min: 3.14 V
• Maximum Operating Temperature: + 70 C
• Package / Case: SSOP-48
• Ethernet Connection Type: 100Base-TX, 10Base-T
• Maximum Supply Current: 160 mA
• Minimum Operating Temperature: 0 C
• Standard Supported: 802.3
• Part # Aliases: ICS1893AFLF

8.13 Register 18: 10Base-T Operations Register
8.13.1 Remote Jabber Detect (bit 18.15)
ICS1893AF, Rev. D 10/26/04
The 10Base-T Operations Register provides an STA with the ability to monitor and control the ICS1893AF
activity while the ICS1893AF is operating in 10Base-T mode.
Note:
1. For an explanation of acronyms used in
2. During any write operation to any bit in this register, the STA must write the default value to all
Table 8-20. 10Base-T Operations Register (register 18 [0x12])
The Remote Jabber Detect bit is provided to indicate that an ICS1893AF port has detected a Jabber
Condition on its receive path. This bit is reset to logic zero on a read of the 10Base-T operations register.
When this bit is logic:
•
•
This bit is a latching high bit. (For more information on latching high and latching low bits, see
8.1.4.1, “Latching High Bits”
Note:
18.15
18.14
18.13
18.12
18.11
18.10
18.9
18.8
18.7
18.6
18.5
18.4
18.3
18.2
18.1
18.0
Bit
Zero, it indicates a Jabber Condition has not occurred on the port’s receive path since either the last read
of this register or the last reset of the associated port.
One, it indicates a Jabber Condition has occurred on the port’s receive path since either the last read of
this register or the last reset of the associated port.
ICS1893AF Data Sheet - Release
Reserved bits.
This bit is provided for information purposes only (that is, no actions are taken by the port). The
ISO/IEC specification defines the Jabber Condition in terms of a port’s transmit path. To set this bit,
an ICS1893AF port monitors its receive path and applies the ISO/IEC Jabber criteria to its receive
path.
Remote Jabber
Detect
Polarity reversed
ICS reserved
ICS reserved
ICS reserved
ICS reserved
ICS reserved
ICS reserved
ICS reserved
ICS reserved
Jabber inhibit
ICS reserved
Auto polarity inhibit
SQE test inhibit
Link Loss inhibit
Squelch inhibit
Definition
No Remote Jabber
Condition detected
Normal polarity
Read unspecified
Polarity automatically
corrected
Normal SQE test behavior
Normal Link Loss behavior Link Always = Link Pass
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Normal Jabber behavior
Read unspecified
Normal squelch behavior
and
Copyright © 2004, Integrated Circuit Systems, Inc.
Section 8.1.4.2, “Latching Low
When Bit = 0
All rights reserved.
Table
93
8-20, see
Remote Jabber Condition
Detected
Polarity reversed
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Read unspecified
Polarity not automatically
corrected
SQE test disabled
No squelch
Jabber Check disabled
When Bit = 1
Chapter 1, “Abbreviations and
Bits”.)
Chapter 8 Management Register Set
RW/0
RW/0
RW/0
RW/0
RW/0
RW/0
RW/0
RW/0
RW/1
cess
RW
RW
RW
RW
RW
Ac-
RO
RO
SF
LH
LH
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Acronyms”.
October, 2004
Section
fault
De-
0
0
–
–
–
–
–
–
–
–
0
1
0
0
0
0
Hex
–
–
–
0