PIC18F67K22-I/MR Microchip Technology, PIC18F67K22-I/MR Datasheet - Page 286

• Manufacturer Part Number: PIC18F67K22-I/MR
• Description: 128kB Flash, 4kB RAM, 1kB EE, NanoWatt XLP, GP 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F67K22-I/MR

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87K22 FAMILY
21.3.6
The master can initiate the data transfer at any time
because it controls the SCKx. The master determines
when the slave (Processor 1,
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPxBUF register is written to. If the SPI
is only going to receive, the SDOx output could be dis-
abled (programmed as an input). The SSPxSR register
will continue to shift in the signal present on the SDIx
pin at the programmed clock rate. As each byte is
received, it will be loaded into the SSPxBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
The clock polarity is selected by appropriately
programming the CKP bit (SSPxCON1<4>). This, then,
would give waveforms for SPI communication, as
FIGURE 21-3:
DS39960D-page 286
Write to
SSPxBUF
SCKx
(CKP = 0
CKE = 0)
SCKx
(CKP = 1
CKE = 0)
SCKx
(CKP = 0
CKE = 1)
SCKx
(CKP = 1
CKE = 1)
SDOx
(CKE = 0)
SDOx
(CKE = 1)
SDIx
(SMP = 0)
Input
Sample
(SMP = 0)
SDIx
(SMP = 1)
Input
Sample
(SMP = 1)
SSPxIF
SSPxSR to
SSPxBUF
MASTER MODE
SPI MODE WAVEFORM (MASTER MODE)
bit 7
bit 7
bit 7
bit 7
Figure
bit 6
bit 6
21-2) is to
bit 5
bit 5
bit 4
bit 4
bit 3
bit 3
shown in
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user-programmable to be one
of the following:
• F
• F
• F
• Timer2 output/2
This allows a maximum data rate (at 40 MHz) of
10.00 Mbps.
Figure 21-3
When the CKE bit is set, the SDOx data is valid before
there is a clock edge on SCKx. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPxBUF is loaded with the received
data is shown.
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
bit 2
bit 2
Figure
shows the waveforms for Master mode.
CY
)
bit 1
bit 1
21-3,
 2009-2011 Microchip Technology Inc.
CY
CY
)
)
Figure 21-5
bit 0
bit 0
bit 0
bit 0
Next Q4 Cycle
after Q2
and
4 Clock
Modes
Figure
21-6,