PIC18F6621-I/PT Microchip Technology Inc., PIC18F6621-I/PT Datasheet - Page 215

• Manufacturer Part Number: PIC18F6621-I/PT
• Description: 64 PIN, 64 KB FLASH, 3840 RAM, 52 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F6621-I/PT

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 54
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 64K Bytes
• Ram Size: 3.8K Bytes
• Speed: 40 MHz
• Timers: 2-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

19.0
The Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) module is one of the
two serial I/O modules. (USART is also known as a
Serial Communications Interface or SCI.) The EUSART
can be configured as a full-duplex asynchronous system
that can communicate with peripheral devices, such as
CRT terminals and personal computers. It can also be
configured as a half-duplex synchronous system that
can communicate with peripheral devices, such as A/D
or D/A integrated circuits, serial EEPROMs, etc.
The Enhanced USART module implements additional
features, including automatic baud rate detection and
calibration, automatic wake-up on Sync Break recep-
tion and 12-bit Break character transmit. These make it
ideally suited for use in Local Interconnect Network bus
(LIN bus) systems.
The EUSART can be configured in the following
modes:
• Asynchronous (full duplex) with:
• Synchronous – Master (half duplex) with
• Synchronous – Slave (half duplex) with selectable
 2005 Microchip Technology Inc.
- Auto-Wake-up on character reception
- Auto-Baud calibration
- 12-bit Break character transmission
selectable clock polarity
clock polarity
ENHANCED UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (EUSART)
PIC18F6525/6621/8525/8621
The pins of USART1 and USART2 are multiplexed with
the functions of PORTC (RC6/TX1/CK1 and RC7/RX1/
DT1) and PORTG (RG1/TX2/CK2 and RG2/RX2/DT2),
respectively. In order to configure these pins as an
EUSART:
• For USART1:
• For USART2:
The operation of each Enhanced USART module is
controlled through three registers:
• Transmit Status and Control (TXSTAx)
• Receive Status and Control (RCSTAx)
• Baud Rate Control (BAUDCONx)
These are detailed on the following pages in
Register 19-1,
respectively.
- bit SPEN (RCSTA1<7>) must be set (= 1)
- bit TRISC<7> must be set (= 1)
- bit TRISC<6> must be cleared (= 0) for
- bit TRISC<6> must be set (= 1) for
- bit SPEN (RCSTA2<7>) must be set (= 1)
- bit TRISG<2> must be set (= 1)
- bit TRISG<1> must be cleared (= 0) for
- bit TRISC<6> must be set (= 1) for
Note:
Note:
Asynchronous and Synchronous Master
modes
Synchronous Slave mode
Asynchronous and Synchronous Master
modes
Synchronous Slave mode
The EUSART control will automatically
reconfigure the pin from input to output as
needed.
Throughout this section, references to
register and bit names that may be associ-
ated with a specific EUSART module are
referred to generically by the use of ‘x’ in
place of the specific module number.
Thus, “RCSTAx” might refer to the
Receive Status register for either USART1
or USART2
Register 19-2
and
DS39612B-page 213
Register 19-3,