S9S12XS256J0CAL Freescale Semiconductor, S9S12XS256J0CAL Datasheet - Page 258

• Manufacturer Part Number: S9S12XS256J0CAL
• Description: MCU 256K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12XS256J0CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 8K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12XS
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12XSFAME, EVB9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

S12XE Clocks and Reset Generator (S12XECRGV1)
8.4.3
This section summarizes the low power options available in the S12XECRG.
8.4.3.1
This is the default mode after reset.
The RTI can be stopped by setting the associated rate select bits to zero.
The COP can be stopped by setting the associated rate select bits to zero.
8.4.3.2
The WAI instruction puts the MCU in a low power consumption stand-by mode depending on setting of
the individual bits in the CLKSEL register. All individual Wait Mode configuration bits can be superposed.
This provides enhanced granularity in reducing the level of power consumption during Wait Mode.
Table 8-15
After executing the WAI instruction the core requests the S12XECRG to switch MCU into Wait Mode.
The S12XECRG then checks whether the PLLWAI bit is asserted. Depending on the configuration the
S12XECRG switches the system and core clocks to OSCCLK by clearing the PLLSEL bit and disables the
IPLL.
There are two ways to restart the MCU from Wait Mode:
258
1. Any reset
2. Any interrupt
lists the individual configuration bits and the parts of the MCU that are affected in Wait Mode.
Low Power Options
Run Mode
Wait Mode
In order to detect a potential clock loss the CME bit should always be
enabled (CME = 1).
If CME bit is disabled and the MCU is configured to run on PLLCLK, a loss
of external clock (OSCCLK) will not be detected and will cause the system
clock to drift towards lower frequencies. As soon as the external clock is
available again the system clock ramps up to its IPLL target frequency. If
the MCU is running on external clock any loss of clock will cause the
system to go static.
Table 8-15. MCU Configuration During Wait Mode
IPLL
COP
RTI
S12XS Family Reference Manual, Rev. 1.11
Stopped
PLLWAI
—
—
NOTE
Stopped
RTIWAI
—
—
COPWAI
Stopped
—
—
Freescale Semiconductor