S9S12XS256J0CAL Freescale Semiconductor, S9S12XS256J0CAL Datasheet - Page 459

• Manufacturer Part Number: S9S12XS256J0CAL
• Description: MCU 256K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12XS256J0CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 8K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12XS
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12XSFAME, EVB9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.4.7.3
Stop mode is dependent on the system. The SPI enters stop mode when the module clock is disabled (held
high or low). If the SPI is in master mode and exchanging data when the CPU enters stop mode, the
transmission is frozen until the CPU exits stop mode. After stop, data to and from the external SPI is
exchanged correctly. In slave mode, the SPI will stay synchronized with the master.
The stop mode is not dependent on the SPISWAI bit.
15.4.7.4
The reset values of registers and signals are described in
Definition”, which details the registers and their bit fields.
15.4.7.5
The SPI only originates interrupt requests when SPI is enabled (SPE bit in SPICR1 set). The following is
a description of how the SPI makes a request and how the MCU should acknowledge that request. The
interrupt vector offset and interrupt priority are chip dependent.
The interrupt flags MODF, SPIF, and SPTEF are logically ORed to generate an interrupt request.
15.4.7.5.1
MODF occurs when the master detects an error on the SS pin. The master SPI must be configured for the
MODF feature (see
changed:
The MODF interrupt is reflected in the status register MODF flag. Clearing the flag will also clear the
interrupt. This interrupt will stay active while the MODF flag is set. MODF has an automatic clearing
process which is described in
Freescale Semiconductor
•
•
•
If a data transmission occurs in slave mode after reset without a write to SPIDR, it will transmit
garbage, or the data last received from the master before the reset.
Reading from the SPIDR after reset will always read zeros.
MSTR = 0, The master bit in SPICR1 resets.
SPI in Stop Mode
Reset
Interrupts
Care must be taken when expecting data from a master while the slave is in
wait or stop mode. Even though the shift register will continue to operate,
the rest of the SPI is shut down (i.e., a SPIF interrupt will not be generated
until exiting stop or wait mode). Also, the byte from the shift register will
not be copied into the SPIDR register until after the slave SPI has exited wait
or stop mode. In slave mode, a received byte pending in the receive shift
register will be lost when entering wait or stop mode. An SPIF flag and
SPIDR copy is generated only if wait mode is entered or exited during a
tranmission. If the slave enters wait mode in idle mode and exits wait mode
in idle mode, neither a SPIF nor a SPIDR copy will occur.
MODF
Table
15-3). After MODF is set, the current transfer is aborted and the following bit is
Section 15.3.2.4, “SPI Status Register
S12XS Family Reference Manual, Rev. 1.11
NOTE
Section 15.3, “Memory Map and Register
(SPISR)”.
Serial Peripheral Interface (S12SPIV5)
459