HD64F3337YCP16V Renesas Electronics America, HD64F3337YCP16V Datasheet - Page 411

• Manufacturer Part Number: HD64F3337YCP16V
• Description: MCU 3/5V 60K PB-FREE 84-PLCC
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300r

Specifications of HD64F3337YCP16V

• Core Size: 8-Bit
• Program Memory Size: 60KB (60K x 8)
• Oscillator Type: Internal
• Core Processor: H8/300
• Speed: 16MHz
• Connectivity: Host Interface, I²C, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 74
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 84-PLCC
• No. Of I/o's: 74
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• No. Of Timers: 6
• No. Of Pwm Channels: 2
• Digital Ic Case Style: PLCC
• Controller Family/series: H8/300
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Bits 7 to 4—Reserved: These bits cannot be modified, and are always read as 1.
Bits 3 to 0—Large Block 3 to 0 (LB3 to LB0): These bits select large blocks (LB3 to LB0) to be
programmed and erased.
Bits 3 to 0:
LB3 to LB0
0
1
19.2.3
EBR2 is an 8-bit register that designates small flash-memory blocks for programming and erasure.
EBR2 is initialized to H'00 by a reset, in the standby modes, and when 12 V is not applied to the
FV
programmed and erased. Figure 19.2 and table 19.6 show a block map.
Note: * The initial value is H'00 in modes 2 and 3 (on-chip ROM enabled). In mode 1 (on-chip ROM
Bits 7 to 0—Small Block 7 to 0 (SB7 to SB0): These bits select small blocks (SB7 to SB0) to be
programmed and erased.
Bits 7 to 0:
SB7 to SB0
0
1
Bit
Initial value
Read/Write
PP
pin. When a bit in EBR2 is set to 1, the corresponding block is selected and can be
disabled), this register cannot be modified and always reads H'FF. For information on
accessing this register, refer to in section 19.7 Flash Memory Programming and erasing
Precautions (11).
Erase Block Register 2 (EBR2)
R/W*
SB7
Description
Block (LB3 to LB0) is not selected
Block (LB3 to LB0) is selected
Description
Block (SB7 to SB0) is not selected
Block (SB7 to SB0) is selected
7
0
R/W*
SB6
6
0
R/W*
SB5
5
0
R/W*
SB4
4
0
R/W*
SB3
3
0
R/W*
SB2
2
0
R/W*
SB1
1
0
(Initial value)
(Initial value)
R/W*
SB0
0
0
379