WM8352GEB/V Wolfson Microelectronics, WM8352GEB/V Datasheet - Page 136

• Manufacturer Part Number: WM8352GEB/V
• Description: Audio CODECs Audio CODEC plus pwr management
• Manufacturer: Wolfson Microelectronics

Specifications of WM8352GEB/V

• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 2
• Conversion Rate: 48 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, 4-Wire)
• Resolution: 12 bit
• Operating Supply Voltage: 3.7 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: BGA
• Minimum Operating Temperature: - 25 C
• Number Of Channels: 2 ADC/2 DAC
• Supply Current: 260 uA
• Thd Plus Noise: - 83 dB
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 2
• No. Of Input Channels: 8
• No. Of Output Channels: 6
• Adc / Dac Resolution: 24bit
• Adcs / Dacs Signal To Noise Ratio: 95dB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

WM8352
w
R201 (C9h)
for LDO1
R204 (CCh)
for LDO2
R207 (CFh)
for LDO3
R210 (D2h)
for LDO4
Note: n is a number between 1 and 4 that identifies the individual DC-DC converter
Table 81 Enabling and Disabling the LDO Regulators
14.7.2
The LDO Regulators can be configured to operate in different modes using the register bits
described in Table 82.
In Switch mode, the Regulators operate as current-limited switches with no voltage regulation.
In LDO Regulator mode, the Regulators generate an output voltage determined by the LDOn_VSEL
fields. The LDO Regulators are dynamically programmable - the output voltage may be adjusted in
software at any time. The Regulators are critically damped to ensure there is no voltage overshoot or
undershoot when adjusting the output voltage.
The default output voltage for the LDO Regulators is set by writing to the LDOn_VSEL register bits.
The ‘image’ voltage settings LDOn_VIMG are alternate values that may be invoked when the
HIBERNATE software or hardware control is asserted.
R200 (C8h)
for LDO1
R203 (CBh)
for LDO2
R206 (CEh)
for LDO3
R209 (D1h)
for LDO4
R202 (CAh)
for LDO1
R205 (CDh)
for LDO2
R208 (D0h)
for LDO3
R211 (D3h)
for LDO4
Note: n is a number between 1 and 4 that identifies the individual LDO regulator
Table 82 Controlling Regulator Voltage and Switch Mode
ADDRESS
ADDRESS
LDO REGULATOR CONTROL
BIT
4:0
4:0
14
13:10
9:6
BIT
LDOn_SWI
LDOn_VSEL
[4:0]
LDOn_VIMG
[4:0]
LABEL
LDOn_ENSL
OT [3:0]
LDOn_SDSL
OT [3:0]
LABEL
on CONFIG
Dependant
DEFAULT
settings
1 1100
0
Dependant
DEFAULT
CONFIG
settings
0000
on
LDOn Regulator mode
0 = LDO voltage regulator
1 = Current-limited switch (no voltage
LDOn Regulator output voltage (when
LDOn_SWI=0)
1 1111 = 3.3V
… (100mV steps)
1 0000 = 1.8V
0 1111 = 1.65V
… (50mV steps)
0 0000 = 0.9V
LDOn Regulator output image voltage
1 1111 = 3.3V
… (100mV steps)
1 0000 = 1.8V
0 1111 = 1.65V
… (50mV steps)
0 0000 = 0.9V
regulation, LDOn_VSEL has no effect)
Time slot for LDOn start-up
0000 = Disabled (do not start up)
0001 = Start-up in time slot 1
… (total 14 slots available)
1110 = Start-up in time slot 14
1111 = Start up on entering ACTIVE
Time slot for LDOn shutdown.
0000 = Shut down on entering OFF
0001 = Shutdown in time slot 1
…. (total 14 slots available)
1110 = Shutdown in time slot 14
1111 = Shut down on entering OFF
DESCRIPTION
PD, March 2010, Rev 4.2
DESCRIPTION
Production Data
136