WM8352GEB/V Wolfson Microelectronics, WM8352GEB/V Datasheet - Page 223

• Manufacturer Part Number: WM8352GEB/V
• Description: Audio CODECs Audio CODEC plus pwr management
• Manufacturer: Wolfson Microelectronics

Specifications of WM8352GEB/V

• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 2
• Conversion Rate: 48 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, 4-Wire)
• Resolution: 12 bit
• Operating Supply Voltage: 3.7 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: BGA
• Minimum Operating Temperature: - 25 C
• Number Of Channels: 2 ADC/2 DAC
• Supply Current: 260 uA
• Thd Plus Noise: - 83 dB
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 2
• No. Of Input Channels: 8
• No. Of Output Channels: 6
• Adc / Dac Resolution: 24bit
• Adcs / Dacs Signal To Noise Ratio: 95dB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Production Data
REGISTER
Register 05h System Hibernate
w
REGISTER
ADDRESS
ADDRESS
R6 (06h)
Interface
Control
BIT
14:13
BIT
1
0
15
12
11
9
3
TEMPMON_HIB_MODE
RECONFIG_AT_ON
PCCOMP_HIB_MODE
USE_DEV_PINS
DEV_ADDR[1:0]
CONFIG_DONE
AUTOINC
SPI_CFG
LABEL
LABEL
DEFAULT
DEFAULT
00
1
0
1
1
0
0
0
Selects which pins to use for the 2-wire control:
0 = Use 2-wire I/F pins as 2-wire interface
1 = Use GPIO 10 and 11 as 2-wire interface, e.g.
to download settings from PIC.
Only applies when CONFIG pins[1:0] = 00.
Reset by state machine.
Selects device address (only valid when
CONF_STS = 00)
00 = 0x34
01 = 0x36
10 = 0x3C
11 = 0x3E
Reset by state machine.
Tells the system that the PIC micro has
completed its programming.
0 = Programming still to be done
1 = Programming complete
Only applies when CONFIG pins[1:0] = 00.
Reset by state machine.
Selects whether to reset the registers in the OFF
state and whether to reload the device
configuration from the PIC when an ON event
occurs.
0 = Do not reset registers in the OFF state. Do not
load configuration data when an ON event occurs.
1 = Reset registers in the OFF state. Load
configuration from the PIC when an ON event
occurs.
Note that, in development mode, the device
configuration from the PIC is always loaded when
first powering up the chip.
This bit must always be set to default (1) in
Custom Modes 01, 10 and 11.
Enables address auto-increment
0 = disabled
1 = enabled
Reset by state machine.
Controls the SDOUT (GPIO6) pin operation in 4
wire mode
0 = SDOUT output is CMOS
1 = SDOUT output is open drain
Note: SPI_4WIRE must be set for this to take
effect.
Protected by security key. Default held in metal
Function of the Hysteresis Comp in hibernate.
0 = Hysteresis Comp is not used in hibernate
1 = Hysteresis Comp is on in hibernate
Function of the temp monitoring in hibernate.
0 = Temp monitoring is off in hibernate state
1 = Temp monitoring is on in the hibernate
state
DESCRIPTION
DESCRIPTION
PD, March 2010, Rev 4.2
REFER TO
REFER TO
WM8352
223