PIC16F887-I/PT Microchip Technology Inc., PIC16F887-I/PT Datasheet - Page 37

• Manufacturer Part Number: PIC16F887-I/PT
• Description: MCU, 8-Bit, 8KW Flash, 368 RAM, 36 I/O, TQFP-44
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F887-I/PT

• A/d Inputs: 14-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Frequency: 20 MHz
• Input Output: 35
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin TFQP
• Programmable Memory: 14K Bytes
• Ram Size: 368 Bytes
• Resistance, Drain To Source On: Bytes
• Serial Interface: MSSP or EUSART
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

2.2.2.7
The PIR2 register contains the interrupt flag bits, as
shown in Register 2-7.
REGISTER 2-7:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
OSFIF
R/W-0
PIR2 Register
OSFIF: Oscillator Fail Interrupt Flag bit
1 = System oscillator failed, clock input has changed to INTOSC (must be cleared in software)
0 = System clock operating
C2IF: Comparator C2 Interrupt Flag bit
1 = Comparator output (C2OUT bit) has changed (must be cleared in software)
0 = Comparator output (C2OUT bit) has not changed
C1IF: Comparator C1 Interrupt Flag bit
1 = Comparator output (C1OUT bit) has changed (must be cleared in software)
0 = Comparator output (C1OUT bit) has not changed
EEIF: EE Write Operation Interrupt Flag bit
1 = Write operation completed (must be cleared in software)
0 = Write operation has not completed or has not started
BCLIF: Bus Collision Interrupt Flag bit
1 = A bus collision has occurred in the MSSP when configured for I
0 = No bus collision has occurred
ULPWUIF: Ultra Low-Power Wake-up Interrupt Flag bit
1 = Wake-up condition has occurred (must be cleared in software)
0 = No Wake-up condition has occurred
Unimplemented: Read as ‘0’
CCP2IF: CCP2 Interrupt Flag bit
Capture mode:
Compare mode:
PWM mode:
Unused in this mode
R/W-0
C2IF
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PIR2: PERIPHERAL INTERRUPT REQUEST REGISTER 2
W = Writable bit
‘1’ = Bit is set
R/W-0
C1IF
PIC16F882/883/884/886/887
R/W-0
EEIF
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
BCLIF
R/W-0
Note:
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE of the INTCON register.
User
appropriate interrupt flag bits are clear prior
to enabling an interrupt.
ULPWUIF
R/W-0
software
2
C Master mode
x = Bit is unknown
U-0
should
—
DS41291D-page 35
ensure
CCP2IF
R/W-0
bit 0
the