RC28F256P30TFB Micron Technology Inc, RC28F256P30TFB Datasheet - Page 45

• Manufacturer Part Number: RC28F256P30TFB
• Manufacturer: Micron Technology Inc

Specifications of RC28F256P30TFB

• Cell Type: NOR
• Density: 256Mb
• Access Time (max): 100ns
• Interface Type: Parallel/Serial
• Boot Type: Top
• Address Bus: 24b
• Operating Supply Voltage (typ): 1.8V
• Operating Temp Range: -40C to 85C
• Package Type: EZBGA
• Sync/async: Async/Sync
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 1.7V
• Operating Supply Voltage (max): 2V
• Word Size: 16b
• Number Of Words: 16M
• Supply Current: 31mA
• Mounting: Surface Mount
• Pin Count: 64
• Lead Free Status / Rohs Status: Not Compliant

P30-65nm
Table 19: Burst Sequence Word Ordering (Sheet 2 of 2)
11.2.7
11.2.8
11.2.9
11.3
Datasheet
45
14
15
1
2
3
4
5
6
7
1
1
1
1
1
1
1
1
1
Clock Edge
The Clock Edge (CE) bit selects either a rising (default) or falling clock edge for CLK.
This clock edge is used at the start of a burst cycle, to output synchronous data, and to
assert/deassert WAIT.
Burst Wrap
The Burst Wrap (BW) bit determines whether 4-word, 8-word, or 16-word burst length
accesses wrap within the selected word-length boundaries or cross word-length
boundaries. When BW is set, burst wrapping does not occur (default). When BW is
cleared, burst wrapping occurs.
When performing synchronous burst reads with BW set (no wrap), an output delay may
occur when the burst sequence crosses its first device-row (16-word) boundary. If the
burst sequence’s start address is 4-word aligned, then no delay occurs. If the start
address is at the end of a 4-word boundary, the worst case output delay is one clock
cycle less than the first access Latency Count. This delay can take place only once, and
doesn’t occur if the burst sequence does not cross a device-row boundary. WAIT
informs the system of this delay when it occurs.
Burst Length
The Burst Length bits (BL[2:0]) select the linear burst length for all synchronous burst
reads of the flash memory array. The burst lengths are 4-word, 8-word, 16-word or
continuous.
Continuous-burst accesses are linear only, and do not wrap within any word length
boundaries (see
cycle begins, the device outputs synchronous burst data until it reaches the end of the
“burstable” address space.
One-Time-Programmable (OTP) Registers
The device contains 17 one-time programmable (OTP) registers that can be used to
implement system security measures and/or device identification. Each OTP register
can be individually locked.
The first 128-bit OTP Register is comprised of two 64-bit (8-word) segments. The lower
64-bit segment is pre-programmed at the Numonyx factory with a unique 64-bit
number. The upper 64-bit segment, as well as the other sixteen 128-bit OTP Registers,
1-2-3-4
2-3-4-5
3-4-5-6
Table 19, “Burst Sequence Word Ordering” on page
7-8-9-10-11-12-13-14
6-7-8-9-10-11-12-13
5-6-7-8-9-10-11-12
4-5-6-7-8-9-10-11
3-4-5-6-7-8-9-10
1-2-3-4-5-6-7-8
2-3-4-5-6-7-8-9
14-15-16-17-18…28-29
15-16-17-18-19…29-30
7-8-9-10-11…21-22
6-7-8-9-10…20-21
1-2-3-4-5…15-16
2-3-4-5-6…16-17
3-4-5-6-7…17-18
4-5-6-7-8…18-19
5-6-7-8-9…19-20
Order Number: 320002-10
14-15-16-17-18-19-20-
15-16-17-18-19-20-21-
44). When a burst
7-8-9-10-11-12-13…
6-7-8-9-10-11-12-…
5-6-7-8-9-10-11…
4-5-6-7-8-9-10…
1-2-3-4-5-6-7-…
2-3-4-5-6-7-8-…
3-4-5-6-7-8-9-…
…
…
Mar 2010