ort82g5 Lattice Semiconductor Corp., ort82g5 Datasheet - Page 51
![no-image](/images/manufacturer_photos/0/3/382/lattice_semiconductor_corp__sml.jpg)
ort82g5
Manufacturer Part Number
ort82g5
Description
Xaui And Fc Fpscs
Manufacturer
Lattice Semiconductor Corp.
Datasheet
1.ORT82G5.pdf
(119 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ort82g5-1F680C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Company:
Part Number:
ort82g5-1F680I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Company:
Part Number:
ort82g5-1FN680C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Company:
Part Number:
ort82g5-1FN680I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Company:
Part Number:
ort82g5-2F680C
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Lattice Semiconductor
Start Up Sequence for the ORT82G5
The following sequence is required by the ORT82G5 device. For information required for simulation that may be dif-
ferent than this sequence, see the ORT82G5 Design Kit.
1. Initiate a hardware reset by making PASB_RESETN low. Keep this low during FPGA configuration of the
2. Configure the following SERDES internal and external registers. Note that after device initialization, all alarm
3. If 8b/10b mode is enabled, enable link synchronization by periodically sending the following sequence three
times:
device. The device will be ready for operation 3 ms after the low to high transition of PASB_RESETN.
and status bits should be read once to clear them. A subsequent read will provide the valid state. Set the fol-
lowing bits in register 30800:
– Bits LCKREFN_[AA:AD] to 1, which implies lock to data.
– Bits ENBYSYNC_[AA:AD] to 1 which enables dynamic alignment to comma.
Set the following bits in register 30801:
– Bits LOOPENB_[AA:AD] to 1 if high-speed serial loopback is desired.
Set the following bits in register 30900:
– Bits LCKREFN_[BA:BD] to 1 which implies lock to data.
– Bits ENBYSYNC_[BA:BD] to 1 which enables dynamic alignment to comma.
Set the following bits in register 30901:
– Bits LOOPENB_[BA:BD] to 1 if high-speed serial loopback is desired.
Set the following bits in registers 30002, 30012, 30022, 30032, 30102, 30112, 30122, 30132:
– TXHR set to 1 if TX half-rate is desired.
– 8B10BT set to 1
Set the following bits in registers 30003, 30013, 30023, 30033, 30103, 30113, 30123, 30133:
– RXHR Set to 1 if RX half-rate is desired.
– 8B10BR set to 1.
– LINKSM set to 1 if the Fibre Channel state machine is desired.
Assert GSWRST bit by writing two 1’s. Deassert GSWRST bit by writing two 0’s. Wait 3ms. If higher speed
serial loopback has been selected, the receive PLLs will use this time to lock to the new serial data.
Monitor the following alarm bits in registers 30000, 30010, 30020, 30030, 30100, 30110, 30120, 30130:
– LKI, PLL lock indicator. 1 indicates that PLL has achieved lock.
– K28.5 D21.4 D21.5 D21.5 or any other idle ordered set (starting with a /comma/) in FC mode.
– /comma/ characters for the XAUI state machine and /A/ characters for word and channel alignment in XAUI
mode.
51
ORCA ORT42G5 and ORT82G5 Data Sheet