C8051T611-GM Silicon Laboratories Inc, C8051T611-GM Datasheet - Page 112

• Manufacturer Part Number: C8051T611-GM
• Description: IC 8051 MCU 16K BYTE-PROG 28-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051T61xr

Specifications of C8051T611-GM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: OTP
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-QFN
• Processor Series: C8051T6x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 29
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051FT610DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 21 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1436-5

C8051T610/1/2/3/4/5/6/7
20.3.1. External RC Example
If an RC network is used as an external oscillator source for the MCU, the circuit should be configured as
shown in Figure 20.1, “RC Mode”. The capacitor should be no greater than 100 pF; however for very small
capacitors, the total capacitance may be dominated by parasitic capacitance in the PCB layout. To deter-
mine the required External Oscillator Frequency Control value (XFCN) in the OSCXCN Register, first
select the RC network value to produce the desired frequency of oscillation, according to Equation 20.1,
where f = the frequency of oscillation in MHz, C = the capacitor value in pF, and R = the pull-up resistor
value in k.
For example: If the frequency desired is 100 kHz, let R = 246 k and C = 50 pF:
f = 1.23( 10
Referring to the table in SFR Definition 20.4, the required XFCN setting is 010b.
20.3.2. External Capacitor Example
If a capacitor is used as an external oscillator for the MCU, the circuit should be configured as shown in
Figure 20.1, “C Mode”. The capacitor should be no greater than 100 pF; however for very small capacitors,
the total capacitance may be dominated by parasitic capacitance in the PCB layout. To determine the
required External Oscillator Frequency Control value (XFCN) in the OSCXCN Register, select the capaci-
tor to be used and find the frequency of oscillation according to Equation 20.2, where f = the frequency of
oscillation in MHz, C = the capacitor value in pF, and V
For example: Assume V
f = KF / (C x VDD)
0.150 MHz = KF / (C x 3.0)
Since the frequency of roughly 150 kHz is desired, select the K Factor from the table in SFR Definition 20.4
(OSCXCN) as KF = 22:
0.150 MHz = 22 / (C x 3.0)
C x 3.0 = 22 / 0.150 MHz
C = 146.6 / 3.0 pF = 48.8 pF
Therefore, the XFCN value to use in this example is 011b and C = 50 pF.
112
3
) / RC = 1.23 ( 10
Equation 20.1. RC Mode Oscillator Frequency
DD
Equation 20.2. C Mode Oscillator Frequency
= 3.0 V and f = 150 kHz:
3
) / [ 246 x 50 ] = 0.1 MHz = 100 kHz
f
f
=
=
1.23 10

KF
Rev 1.0




R V
3
DD



R C
= the MCU power supply in Volts.
DD


