C8051T611-GM Silicon Laboratories Inc, C8051T611-GM Datasheet - Page 57

• Manufacturer Part Number: C8051T611-GM
• Description: IC 8051 MCU 16K BYTE-PROG 28-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051T61xr

Specifications of C8051T611-GM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: OTP
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-QFN
• Processor Series: C8051T6x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 29
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051FT610DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 21 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1436-5

SFR Definition 11.1. REG0CN: Voltage Regulator Control
SFR Address = 0xC7
Name
Reset
Bit
5:1
Type
7
6
0
Bit
Reserved Reserved. Must Write 00000b.
STOPCF Stop Mode Configuration.
BYPASS Bypass Internal Regulator.
MPCE
Name
STOPCF
R/W
7
0
This bit configures the regulator’s behavior when the device enters STOP mode.
0: Regulator is still active in STOP mode. Any enabled reset source will reset the
device.
1: Regulator is shut down in STOP mode. Only the RST pin or power cycle can reset
the device.
This bit places the regulator in bypass mode, turning off the regulator, and allowing the
core to run directly from the V
0: Normal Mode—Regulator is on.
1: Bypass Mode—Regulator is off, and the microcontroller core operates directly from
the V
IMPORTANT: Bypass mode is for use with an external regulator as the supply
voltage only. Never place the regulator in bypass mode when the V
voltage is greater than the specifications given in Table 7.1 on page 31. Doing so
may cause permanent damage to the device.
Memory Power Controller Enable.
This bit can help the system save power at slower system clock frequencies (about
2.0 MHz or less) by automatically shutting down the EPROM memory between clocks
when information is not being fetched from the EPROM memory.
0: Normal Mode—Memory power controller disabled (EPROM memory is always on).
1: Low Power Mode—Memory power controller enabled (EPROM memory turns on/off
as needed).
Note: If an external clock source is used with the Memory Power Controller enabled, and the
BYPASS
DD
R/W
clock frequency changes from slow (<2.0 MHz) to fast (> 2.0 MHz), the EPROM power
will turn on, and up to 20 clocks may be "skipped" to ensure that the EPROM power is
stable before reading memory.
6
0
supply voltage.
R/W
5
0
DD
R/W
Rev 1.0
4
0
supply pin.
C8051T610/1/2/3/4/5/6/7
Function
R/W
3
0
R/W
2
0
R/W
1
0
DD
supply
MPCE
R/W
0
0
57