MCR908JK1ECPE Freescale Semiconductor, MCR908JK1ECPE Datasheet - Page 52

• Manufacturer Part Number: MCR908JK1ECPE
• Description: IC MCU 1.5K FLASH 8MHZ 20-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCR908JK1ECPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 14
• Program Memory Size: 1.5KB (1.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 12x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: HC08JK
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

System Integration Module (SIM)
5.3 Reset and System Initialization
The MCU has these reset sources:
All of these resets produce the vector $FFFE–$FFFF ($FEFE–$FEFF in Monitor mode) and assert the
internal reset signal (IRST). IRST causes all registers to be returned to their default values and all
modules to be returned to their reset states.
An internal reset clears the SIM counter (see
the resets sets a corresponding bit in the reset status register (RSR). (See
5.3.1 External Pin Reset
The RST pin circuits include an internal pull-up device. Pulling the asynchronous RST pin low halts all
processing. The PIN bit of the reset status register (RSR) is set as long as RST is held low for a minimum
of 67 2OSCOUT cycles, assuming that the POR was not the source of the reset. See
Figure 5-4
5.3.2 Active Resets from Internal Sources
All internal reset sources actively pull the RST pin low for 32 2OSCOUT cycles to allow resetting of
external peripherals. The internal reset signal IRST continues to be asserted for an additional 32 cycles
(Figure
(See
the SIM forces the RST pin low. The internal reset signal then follows the sequence from the falling edge
of RST shown in
52
•
•
•
•
•
•
Figure
Power-on reset module (POR)
External reset pin (RST)
Computer operating properly module (COP)
Low-voltage inhibit module (LVI)
Illegal opcode
Illegal address
2OSCOUT
5-5). An internal reset can be caused by an illegal address, illegal opcode, COP time-out, or POR.
shows the relative timing.
5-6.) Note that for POR resets, the SIM cycles through 4096 2OSCOUT cycles during which
RST
IAB
Figure
Reset Type
All others
PC
POR
5-5.
MC68HC908JL3E Family Data Sheet, Rev. 4
Figure 5-4. External Reset Timing
Table 5-2. PIN Bit Set Timing
5.4 SIM
Number of Cycles Required to Set PIN
Counter), but an external reset does not. Each of
4163 (4096 + 64 + 3)
67 (64 + 3)
VECT H VECT L
5.7 SIM
Freescale Semiconductor
Table 5-2
Registers.)
for details.