MCR908JK1ECPE Freescale Semiconductor, MCR908JK1ECPE Datasheet - Page 99

• Manufacturer Part Number: MCR908JK1ECPE
• Description: IC MCU 1.5K FLASH 8MHZ 20-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCR908JK1ECPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 14
• Program Memory Size: 1.5KB (1.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 12x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: HC08JK
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Interrupts
9.3.2 Voltage Conversion
When the input voltage to the ADC equals V
, the ADC converts the signal to $FF (full scale). If the input
DD
voltage equals V
, the ADC converts it to $00. Input voltages between V
and V
are a straight-line
SS
DD
SS
linear conversion. All other input voltages will result in $FF if greater than V
and $00 if less than V
.
DD
SS
NOTE
Input voltage should not exceed the analog supply voltages.
9.3.3 Conversion Time
Fourteen ADC internal clocks are required to perform one conversion. The ADC starts a conversion on
the first rising edge of the ADC internal clock immediately following a write to the ADSCR. If the ADC
internal clock is selected to run at 1MHz, then one conversion will take 14μs to complete. With a 1MHz
ADC internal clock the maximum sample rate is 71.43kHz.
14 ADC Clock Cycles
Conversion Time =
ADC Clock Frequency
Number of Bus Cycles = Conversion Time × Bus Frequency
9.3.4 Continuous Conversion
In the continuous conversion mode, the ADC continuously converts the selected channel filling the ADC
data register with new data after each conversion. Data from the previous conversion will be overwritten
whether that data has been read or not. Conversions will continue until the ADCO bit is cleared. The
COCO bit (ADC status and control register, $003C) is set after each conversion and can be cleared by
writing the ADC status and control register or reading of the ADC data register.
9.3.5 Accuracy and Precision
The conversion process is monotonic and has no missing codes.
9.4 Interrupts
When the AIEN bit is set, the ADC module is capable of generating a CPU interrupt after each ADC
conversion. A CPU interrupt is generated if the COCO bit is at 0. The COCO bit is not used as a
conversion complete flag when interrupts are enabled.
9.5 Low-Power Modes
The following subsections describe the ADC in low-power modes.
9.5.1 Wait Mode
The ADC continues normal operation during wait mode. Any enabled CPU interrupt request from the ADC
can bring the MCU out of wait mode. If the ADC is not required to bring the MCU out of wait mode, power
down the ADC by setting the ADCH[4:0] bits in the ADC status and control register to 1’s before executing
the WAIT instruction.
MC68HC908JL3E Family Data Sheet, Rev. 4
Freescale Semiconductor
99