MC9S08DZ60MLC Freescale Semiconductor, MC9S08DZ60MLC Datasheet - Page 78

• Manufacturer Part Number: MC9S08DZ60MLC
• Description: IC MCU 60K FLASH 4K RAM 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08DZ60MLC

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LQFP
• For Use With: DEMO9S08DZ60 - BOARD DEMOEVB9S08DZ60 - BOARD EVAL FOR 9S08DZ60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1
Any other
Chapter 5 Resets, Interrupts, and General System Control
5.8.2
This high page register includes read-only status flags to indicate the source of the most recent reset. When
a debug host forces reset by writing 1 to BDFR in the SBDFR register, none of the status bits in SRS will
be set. Writing any value to this register address causes a COP reset when the COP is enabled except the
values 0x55 and 0xAA. Writing a 0x55-0xAA sequence to this address clears the COP watchdog timer
without affecting the contents of this register. The reset state of these bits depends on what caused the
MCU to reset.
78
Any of these reset sources that are active at the time of reset entry will cause the corresponding bit(s) to be set; bits
corresponding to sources that are not active at the time of reset entry will be cleared.
reset:
POR:
LVD:
Field
ILOP
ILAD
POR
COP
PIN
7
6
5
4
3
W
R
System Reset Status Register (SRS)
POR
Power-On Reset — Reset was caused by the power-on detection logic. Because the internal supply voltage was
ramping up at the time, the low-voltage reset (LVD) status bit is also set to indicate that the reset occurred while
the internal supply was below the LVD threshold.
0 Reset not caused by POR.
1 POR caused reset.
External Reset Pin — Reset was caused by an active-low level on the external reset pin.
0 Reset not caused by external reset pin.
1 Reset came from external reset pin.
Computer Operating Properly (COP) Watchdog — Reset was caused by the COP watchdog timer timing out.
This reset source can be blocked by COPE = 0.
0 Reset not caused by COP timeout.
1 Reset caused by COP timeout.
Illegal Opcode — Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP
instruction is considered illegal if stop is disabled by STOPE = 0 in the SOPT register. The BGND instruction is
considered illegal if active background mode is disabled by ENBDM = 0 in the BDCSC register.
0 Reset not caused by an illegal opcode.
1 Reset caused by an illegal opcode.
Illegal Address — Reset was caused by an attempt to access either data or an instruction at an unimplemented
memory address.
0 Reset not caused by an illegal address.
1 Reset caused by an illegal address.
1
u
0
7
Note
PIN
0
0
6
(1)
Writing 0x55, 0xAA to SRS address clears COP watchdog timer.
Table 5-3. SRS Register Field Descriptions
Figure 5-3. System Reset Status (SRS)
MC9S08DZ60 Series Data Sheet, Rev. 4
Note
COP
0
0
5
(1)
Note
ILOP
0
0
4
(1)
Description
Note
ILAD
3
0
0
(1)
LOC
0
0
0
2
Freescale Semiconductor
LVD
1
1
0
1
0
0
0
0
0