ST10F272B_12 STMICROELECTRONICS [STMicroelectronics], ST10F272B_12 Datasheet - Page 145
ST10F272B_12
Manufacturer Part Number
ST10F272B_12
Description
16-bit MCU with 256 Kbyte Flash memory and 12/20 Kbyte RAM
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.ST10F272B_12.pdf
(188 pages)
- Current page: 145 of 188
- Download datasheet (3Mb)
ST10F272B/ST10F272E
besides, it sources charge during the sampling phase, when the analog signal source is a
high-impedance source.
A real filter, can typically be obtained by using a series resistance with a capacitor on the
input pin (simple RC Filter). The RC filtering may be limited according to the value of source
impedance of the transducer or circuit supplying the analog signal to be measured. The filter
at the input pins must be designed taking into account the dynamic characteristics of the
input signal (bandwidth).
Figure 39. A/D converter input pins scheme
Input Leakage and external circuit
The series resistor utilized to limit the current to a pin (see R
with a large source impedance can lead to a degradation of A/D converter accuracy when
input leakage is present.
Data about maximum input leakage current at each pin are provided in the Data Sheet (see
Section 24: Electrical
temperatures, and in general it decreases by one half for each 10° C decrease in
temperature.
Considering that, for a 10-bit A/D converter one count is about 5mV (assuming V
an input leakage of 100nA acting though an R
error of exactly one count (5mV); if the resistance were 100kΩ the error would become two
counts.
Eventual additional leakage due to external clamping diodes must also be taken into
account in computing the total leakage affecting the A/D converter measurements. Another
contribution to the total leakage is represented by the charge sharing effects with the
sampling capacitance: being C
equal to the conversion rate of a single channel (maximum when fixed channel continuous
conversion mode is selected), it can be seen as a resistive path to ground. For instance,
assuming a conversion rate of 250kHz, with C
obtained (R
channel). To minimize the error induced by the voltage partitioning between this resistance
EQ
= 1 / f
C
characteristics). Input leakage is greatest at high operating
C
S
, where f
Doc ID 11917 Rev 3
S
substantially a switched capacitance, with a frequency
C
represents the conversion rate at the considered
L
S
= 50kΩ of external resistance leads to an
equal to 4pF, a resistance of 1MΩ is
L
in
Figure
Electrical characteristics
39), in combination
AREF
145/188
= 5V),
Related parts for ST10F272B_12
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: