ATTINY167-15XD Atmel, ATTINY167-15XD Datasheet - Page 175

• Manufacturer Part Number: ATTINY167-15XD
• Description: MCU AVR 16K FLASH 15MHZ 20-TSSOP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY167-15XD

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 20-TSSOP
• Processor Series: ATTINY1x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.5.7.5
15.5.7.6
15.5.8
7728G–AVR–06/10
xxOK Flags
Data Length after Error
Data Length in UART Mode
Figure 15-11. Tx Response - Error
Note:
There are three xxOK flags in LINSIR register:
These flags can generate interrupts if the corresponding enable interrupt bit is set in the LINE-
NIR register (see
• If an error occurs, Tx stops, the corresponding error flag is set and LRXDL will give the
• If no error occurs, LTXOK is set after the transmission of the CHECKSUM, LTXDL will be
• The UART mode forces LRXDL and LTXDL to 0 and disables the writing in LINDLR
• Note that after reset, LRXDL and LTXDL are also forced to 0.
• LIDOK: LIN IDentifier OK
• LRXOK: LIN RX response complete
• LTXOK: LIN TX response complete
number of transmitted bytes without error,
unchanged (and LRXDL = LTXDL).
register,
It is set at the end of the header, either by the Tx Header function or by the Rx Header. In
LIN 1.3, before generating LIDOK, the controller updates the LRXDL & LTXDL fields in
LINDLR register.
It is not driven in UART mode.
It is set at the end of the response by the Rx Response function in LIN mode and once a
character is received in UART mode.
It is set at the end of the response by the Tx Response function in LIN mode and once a
character has been sent in UART mode.
Information on response (ex: error on byte) is only available at the end of the serializa-
tion/de-serialization of the byte.
LIN bus
LBUSY
LRXDL
LTXDL
Section 15.5.13 “Interrupts” on page
4
4
DATA-0
1
LCMD=Tx Response
st
Byte
0
DATA-1
2
nd
Byte
1
LCMD2..0=000
ERROR
178).
ATtiny87/ATtiny167
3
DATA-2
rd
Byte
2
b
LERR
175