ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 155
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 155 of 198
- Download datasheet (5Mb)
11.9
11.9.1
11.9.2
8111C–MCU Wireless–09/09
Configurable Start-Of-Frame Delimiter
Overview
Register Description
The SFD is a field indicating the end of the SHR and the start of the packet data. The length of
the SFD is 1 octet (2 symbols). This octet is used for byte synchronization only and is not
included in the Frame Buffer.
The value of the SFD could be changed if it is needed to operate non IEEE 802.15.4 compliant
networks. An IEEE 802.15.4 compliant network node does not synchronize to frames with a dif-
ferent SFD value.
Due to the way the SHR is formed, it is not recommended to set the low-order 4 bits to 0. The
LSB of the SFD is transmitted first, i.e. right after the last bit of the preamble sequence.
Register 0x0B (SFD_VALUE):
This register contains the one octet start-of-frame delimiter (SFD) to synchronize to a received
frame.
• Bit [7:0] - SFD_VALUE
For compliant IEEE 802.15.4 networks set SFD_VALUE = 0xA7, as specified by
is the default value of the register.
To establish non IEEE 802.15.4 compliant networks the SFD value can be changed to any other
value. If enabled an IRQ_2 (RX_START) is issued only if the received SFD matches the register
content of register SFD_VALUE and a valid PHR is received.
Bit
+0x0B
Read/Write
Reset Value
R/W
7
1
R/W
6
0
R/W
5
1
SFD_VALUE[7:0]
R/W
4
0
R/W
3
0
R/W
2
1
R/W
1
1
AT86RF231
R/W
0
1
[1]
SFD_VALUE
and [2]. This
155
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika