OM11077 NXP Semiconductors, OM11077 Datasheet - Page 211
OM11077
Manufacturer Part Number
OM11077
Description
MODULE DIMM LPC2478 ARM7
Manufacturer
NXP Semiconductors
Specifications of OM11077
Accessory Type
Module Card
For Use With/related Products
ARM-57TS-LPC2478
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-4742
- Current page: 211 of 792
- Download datasheet (5Mb)
1. How to read this chapter
2. Basic configuration
3. Introduction
UM10237_4
User manual
The Ethernet controller is avialable in parts LPC2458 and LPC2460/68/70/78.
The Ethernet controller is configured using the following registers:
The Ethernet block contains a full featured 10 Mbps or 100 Mbps Ethernet MAC (Media
Access Controller) designed to provide optimized performance through the use of DMA
hardware acceleration. Features include a generous suite of control registers, half or full
duplex operation, flow control, control frames, hardware acceleration for transmit retry,
receive packet filtering and wake-up on LAN activity. Automatic frame transmission and
reception with Scatter-Gather DMA off-loads many operations from the CPU.
The Ethernet block and the CPU share a dedicated AHB subsystem (AHB2) that is used
to access the Ethernet SRAM for Ethernet data, control, and status information. All other
AHB traffic in the LPC2400 takes place on a different AHB subsystem, effectively
separating Ethernet activity from the rest of the system. The Ethernet DMA can also
access off-chip memory via the External Memory Controller, as well as the SRAM located
on AHB1, if is not being used by the USB block. However, using memory other than the
Ethernet SRAM, especially off-chip memory, will slow Ethernet access to memory and
increase the loading of AHB1.
The Ethernet block interfaces between an off-chip Ethernet PHY using the MII (Media
Independent Interface) or RMII (reduced MII) protocol. and the on-chip MIIM (Media
Independent Interface Management) serial bus.
1. Power: In the PCONP register
2. Clock: see
3. Pins: Select Ethernet pins and their modes in PINSEL2/3 and PINMODE2/3
4. Wakeup: Use the INTWAKE register
5. Interrupts: Interrupts are enabled in the VIC using the VICIntEnable register
6. Initialization: see
UM10237
Chapter 11: LPC24XX Ethernet
Rev. 04 — 26 August 2009
Remark: On reset, the Ethernet block is disabled (PCENET = 0).
(Section
Ethernet port to wake up the microcontroller from Power-down mode.
(Section
9–5).
7–3.4).
Section
Section
Rev. 04 — 26 August 2009
4–3.3.1.
11–9.5.
(Table
(Section
4–63), set bit PCENET.
4–3.4.8) to enable activity on the
© NXP B.V. 2009. All rights reserved.
User manual
211 of 792
Related parts for OM11077
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: