PIC12C672T-10/SM Microchip Technology, PIC12C672T-10/SM Datasheet - Page 580

• Manufacturer Part Number: PIC12C672T-10/SM
• Description: IC MCU OTP 2KX14 A/D 8-SOIJ
• Manufacturer: Microchip Technology
• Series: PIC® 12Cr

Specifications of PIC12C672T-10/SM

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• For Use With: XLT08SO-1 - SOCKET TRANSITION 8SOIC 150/208AC164312 - MODULE SKT FOR PM3 16SOIC309-1048 - ADAPTER 8-SOIC TO 8-DIP309-1047 - ADAPTER 8-SOIC TO 8-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -

PICmicro MID-RANGE MCU FAMILY
30.7
DS31030A-page 30-10
DC CHARACTERISTICS
D060
D060A
D061
D063
D070
D070A
D160
D160A
D160B
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
Param
No.
† Data in “Typ” column is at 5V, 25 C unless otherwise stated. These parameters are for design guidance only
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified lev-
3: Negative current is defined as current sourced by the pin.
and are not tested.
PICmicro be driven with an external clock while in RC mode.
els represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
Symbol
I
I
PUGIO
PURB
I/O Current Specifications
I
I
PU
IL
Input Leakage Current
I/O ports
CDAC
MCLR
Weak Pull-up Current
PORTB weak pull-up current
GIO weak pull-up current
Programmable Current
Source (Slope A/D devices)
Output Current
The PORT/GIO Weak Pull-up Current is the additional current that the device will draw when
the weak pull-ups are enabled.
Leakage Currents are the currents that the device consumes, since the devices are manufac-
tured in the real world and do not adhere to their ideal characteristics. Ideally there should be no
current on an input, but due to the real world there is always some parasitic path that consumes
negligible current.
Table 30-7:
Characteristic
Example DC Characteristics
(2,3)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Operating voltage V
18.75
1.25
Min
-0.5
50
50
—
—
—
—
33.75 48.75
Typ†
2.25
250
250
—
—
—
—
0
Max
3.25
400
400
0.5
DD
1
1
5
5
range as described in DC spec
0˚C
-40˚C
-40˚C
Units
A
A
A
A
A
A
A
A
A
Vss
Pin at hi-impedance
Vss
Pin at hi-impedance
Vss
Vss
XT, HS and LP osc modes
V
V
CDAC pin = 0V
ADCON1<7:4> = 1111b
(full-scale)
ADCON1<7:4> = 0001b (1 LSB)
ADCON1<7:4> = 0000b
(zero-scale)
T
T
T
DD
DD
A
A
A
= 5V, V
= 5V, V
1997 Microchip Technology Inc.
V
V
V
V
+70˚C for commercial,
+85˚C for industrial and
+125˚C for extended
PIN
PIN
PIN
PIN
Conditions
PIN
PIN
V
V
V
V
DD
DD
DD
DD
= V
= V
,
,
,
SS
SS
Table
30-3.