IC PIC MCU FLASH 16K 28-SSOP

PIC24F16KA102-I/SS

Manufacturer Part NumberPIC24F16KA102-I/SS
DescriptionIC PIC MCU FLASH 16K 28-SSOP
ManufacturerMicrochip Technology
SeriesPIC® XLP™ 24F
PIC24F16KA102-I/SS datasheets
 


Specifications of PIC24F16KA102-I/SS

Program Memory TypeFLASHProgram Memory Size16KB (5.5K x 24)
Package / Case28-SSOPCore ProcessorPIC
Core Size16-BitSpeed32MHz
ConnectivityI²C, IrDA, SPI, UART/USARTPeripheralsBrown-out Detect/Reset, POR, PWM, WDT
Number Of I /o24Eeprom Size512 x 8
Ram Size1.5K x 8Voltage - Supply (vcc/vdd)1.8 V ~ 3.6 V
Data ConvertersA/D 9x10bOscillator TypeInternal
Operating Temperature-40°C ~ 85°CProcessor SeriesPIC24F
CorePICData Bus Width16 bit
Data Ram Size1.5 KBInterface TypeI2C/IrDA/SPI/UART
Maximum Clock Frequency32 MHzNumber Of Programmable I/os24
Number Of Timers3Operating Supply Voltage1.8 V to 3.6 V
Maximum Operating Temperature+ 85 CMounting StyleSMD/SMT
3rd Party Development Tools52713-733, 52714-737, 53276-922, EWDSPICDevelopment Tools By SupplierPG164130, DV164035, DV244005, DV164005, DM240001
Minimum Operating Temperature- 40 COn-chip Adc9-ch x 10-bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantFor Use WithMA240017 - MODULE PLUG-IN PIC24F16KA102 PIM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Page 191
192
Page 192
193
Page 193
194
Page 194
195
Page 195
196
Page 196
197
Page 197
198
Page 198
199
Page 199
200
Page 200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
Page 198/254

Download datasheet (4Mb)Embed
PrevNext
PIC24F16KA102 FAMILY
26.2
Watchdog Timer (WDT)
For the PIC24F16KA102 family of devices, the WDT is
driven by the LPRC oscillator. When the WDT is
enabled, the clock source is also enabled.
The nominal WDT clock source from LPRC is 31 kHz.
This feeds a prescaler that can be configured for either
5-bit (divide-by-32) or 7-bit (divide-by-128) operation.
The prescaler is set by the FWPSA Configuration bit.
With a 31 kHz input, the prescaler yields a nominal
WDT time-out period (T
) of 1 ms in 5-bit mode or
WDT
4 ms in 7-bit mode.
A variable postscaler divides down the WDT prescaler
output and allows for a wide range of time-out periods.
The postscaler is controlled by the Configuration bits,
WDTPS<3:0> (FWDT<3:0>), which allow the selection
of a total of 16 settings, from 1:1 to 1:32,768. Using the
prescaler and postscaler, time-out periods ranging from
1 ms to 131 seconds can be achieved.
The WDT, prescaler and postscaler are reset:
• On any device Reset
• On the completion of a clock switch, whether
invoked by software (i.e., setting the OSWEN bit
after changing the NOSC bits) or by hardware
(i.e., Fail-Safe Clock Monitor)
• When a PWRSAV instruction is executed
(i.e., Sleep or Idle mode is entered)
• When the device exits Sleep or Idle mode to
resume normal operation
• By a CLRWDT instruction during normal execution
If the WDT is enabled, it will continue to run during
Sleep or Idle modes. When the WDT time-out occurs,
the device will wake the device and code execution will
continue from where the PWRSAV instruction was
FIGURE 26-1:
WDT BLOCK DIAGRAM
SWDTEN
FWDTEN
FWPSA
Prescaler
LPRC Input
(5-Bit/7-Bit)
31 kHz
All Device Resets
Transition to
New Clock Source
Exit Sleep or
Idle Mode
CLRWDT Instr.
PWRSAV Instr.
Sleep or Idle Mode
DS39927B-page 196
executed. The corresponding SLEEP or IDLE bits
(RCON<3:2>) will need to be cleared in software after
the device wakes up.
The WDT Flag bit, WDTO (RCON<4>), is not
automatically cleared following a WDT time-out. To
detect subsequent WDT events, the flag must be
cleared in software.
The CLRWDT and PWRSAV instructions
Note:
clear the prescaler and postscaler counts
when executed.
26.2.1
WINDOWED OPERATION
The Watchdog Timer has an optional Fixed Window
mode of operation. In this Windowed mode, CLRWDT
instructions can only reset the WDT during the last 1/4
of the programmed WDT period. A CLRWDT instruction
executed before that window causes a WDT Reset,
similar to a WDT time-out.
Windowed WDT mode is enabled by programming the
Configuration bit, WINDIS (FWDT<6>), to ‘0’.
26.2.2
CONTROL REGISTER
The WDT is enabled or disabled by the FWDTEN
Configuration bit. When the FWDTEN Configuration bit
is set, the WDT is always enabled.
The WDT can be optionally controlled in software when
the FWDTEN Configuration bit has been programmed
to ‘0’. The WDT is enabled in software by setting the
SWDTEN control bit (RCON<5>). The SWDTEN
control bit is cleared on any device Reset. The software
WDT option allows the user to enable the WDT for
critical code segments and disable the WDT during
non-critical segments for maximum power savings.
LPRC Control
WDTPS<3:0>
WDT
Postscaler
Counter
1:1 to 1:32.768
1 ms/4 ms
Preliminary
Wake from Sleep
WDT Overflow
Reset
© 2009 Microchip Technology Inc.