IC PIC MCU FLASH 16K 28-SSOP

PIC24F16KA102-I/SS

Manufacturer Part NumberPIC24F16KA102-I/SS
DescriptionIC PIC MCU FLASH 16K 28-SSOP
ManufacturerMicrochip Technology
SeriesPIC® XLP™ 24F
PIC24F16KA102-I/SS datasheets
 


Specifications of PIC24F16KA102-I/SS

Program Memory TypeFLASHProgram Memory Size16KB (5.5K x 24)
Package / Case28-SSOPCore ProcessorPIC
Core Size16-BitSpeed32MHz
ConnectivityI²C, IrDA, SPI, UART/USARTPeripheralsBrown-out Detect/Reset, POR, PWM, WDT
Number Of I /o24Eeprom Size512 x 8
Ram Size1.5K x 8Voltage - Supply (vcc/vdd)1.8 V ~ 3.6 V
Data ConvertersA/D 9x10bOscillator TypeInternal
Operating Temperature-40°C ~ 85°CProcessor SeriesPIC24F
CorePICData Bus Width16 bit
Data Ram Size1.5 KBInterface TypeI2C/IrDA/SPI/UART
Maximum Clock Frequency32 MHzNumber Of Programmable I/os24
Number Of Timers3Operating Supply Voltage1.8 V to 3.6 V
Maximum Operating Temperature+ 85 CMounting StyleSMD/SMT
3rd Party Development Tools52713-733, 52714-737, 53276-922, EWDSPICDevelopment Tools By SupplierPG164130, DV164035, DV244005, DV164005, DM240001
Minimum Operating Temperature- 40 COn-chip Adc9-ch x 10-bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantFor Use WithMA240017 - MODULE PLUG-IN PIC24F16KA102 PIM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Page 51
52
Page 52
53
Page 53
54
Page 54
55
Page 55
56
Page 56
57
Page 57
58
Page 58
59
Page 59
60
Page 60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
Page 53/254

Download datasheet (4Mb)Embed
PrevNext
6.0
DATA EEPROM MEMORY
This data sheet summarizes the features
Note:
of this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information on Data
EEPROM, refer to the “PIC24F Family
Reference Manual”, Section 5. “Data
EEPROM” (DS39720).
The data EEPROM memory is a Nonvolatile Memory
(NVM), separate from the program and volatile data
RAM. Data EEPROM memory is based on the same
Flash technology as program memory, and is optimized
for both long retention and a higher number of
erase/write cycles.
The data EEPROM is mapped to the top of the user
program memory space, with the top address at
program memory address, 7FFE00h to 7FFFFFh. The
size of the data EEPROM is 256 words in
PIC24F16KA102 devices.
The data EEPROM is organized as 16-bit wide
memory. Each word is directly addressable, and is
readable and writable during normal operation over the
entire V
range.
DD
Unlike the Flash program memory, normal program
execution is not stopped during a data EEPROM
program or erase operation.
The data EEPROM programming operations are
controlled using the three NVM Control registers:
• NVMCON: Nonvolatile Memory Control Register
• NVMKEY: Nonvolatile Memory Key Register
• NVMADR: Nonvolatile Memory Address Register
EXAMPLE 6-1:
DATA EEPROM UNLOCK SEQUENCE
//Disable Interrupts For 5 instructions
asm volatile(“disi #5”);
//Issue Unlock Sequence
asm volatile(“mov #0x55, W0
“mov W0, NVMKEY
“mov #0xAA, W1
“mov W1, NVMKEY
// Perform Write/Erase operations
asm volatile (“bset NVMCON, #WR
“nop
“nop
© 2009 Microchip Technology Inc.
PIC24F16KA102 FAMILY
6.1
NVMCON Register
The NVMCON register (Register 6-1) is also the pri-
mary control register for data EEPROM program/erase
operations. The upper byte contains the control bits
used to start the program or erase cycle, and the flag
bit to indicate if the operation was successfully
performed. The lower byte of NVMCOM configures the
type of NVM operation that will be performed.
6.2
NVMKEY Register
The NVMKEY is a write-only register that is used to
prevent accidental writes or erasures of data EEPROM
locations.
To start any programming or erase sequence, the
following instructions must be executed first, in the
exact order provided:
1.
Write 55h to NVMKEY.
2.
Write AAh to NVMKEY.
After this sequence, a write will be allowed to the
NVMCON register for one instruction cycle. In most
cases, the user will simply need to set the WR bit in the
NVMCON register to start the program or erase cycle.
Interrupts should be disabled during the unlock
sequence.
®
The MPLAB
C30 C compiler provides a defined library
procedure (builtin_write_NVM) to perform the
unlock sequence. Example 6-1 illustrates how the
unlock sequence can be performed with in-line
assembly.
\n”
\n”
\n”
\n”);
\n”
\n”
\n”);
Preliminary
DS39927B-page 51