DSPIC33EP128MC504-I/ML Microchip Technology, DSPIC33EP128MC504-I/ML Datasheet - Page 243

• Manufacturer Part Number: DSPIC33EP128MC504-I/ML
• Description: Digital Signal Processors & Controllers - DSP, DSC 16B 128KB FL 16KBR 60MHz 44P OpAmps
• Manufacturer: Microchip Technology
• Type: dsPIC33E/PIC24Er

Specifications of DSPIC33EP128MC504-I/ML

• Rohs: yes
• Core: dsPIC33E
• Data Bus Width: 16 bit
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Maximum Clock Frequency: 7.37 MHz, 32 kHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5 x 16-bit, 2 x 32-bit
• Device Million Instructions Per Second: 70 MIPs
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Package / Case: TQFP-44
• Mounting Style: SMD/SMT
• Family / Core: dsPIC33E/PIC24E
• Interface Type: CAN, I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• On-chip Adc: Yes
• Product: DSPs
• Program Memory Type: Flash
• Supply Current: 10 mA

REGISTER 16-15: FCLCONx: PWM FAULT CURRENT-LIMIT CONTROL REGISTER
 2011-2012 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-10
bit 9
bit 8
Note 1:
dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
R/W-1
U-0
—
2:
If the PWMLOCK Configuration bit (FOSCSEL<6>) is a ‘1’, the IOCONx register can only be written after
the unlock sequence has been executed.
These bits should be changed only when PTEN = 0. Changing the clock selection during operation will
yield unpredictable results.
Unimplemented: Read as ‘0’
CLSRC<4:0>: Current-Limit Control Signal Source Select bits for PWM Generator #
11111 = Fault 32
11110 = Reserved
•
•
•
01100 = Reserved
01011 = Comparator 4
01010 = Op amp/Comparator 3
01001 = Op amp/Comparator 2
01000 = Op amp/Comparator 1
00111 = Reserved
00110 = Reserved
00101 = Reserved
00100 = Reserved
00011 = Fault 4
00010 = Fault 3
00001 = Fault 2
00000 = Fault 1 (default)
CLPOL: Current-Limit Polarity bit for PWM Generator #
1 = The selected current-limit source is active-low
0 = The selected current-limit source is active-high
CLMOD: Current-Limit Mode Enable bit for PWM Generator #
1 = Current-Limit mode is enabled
0 = Current-Limit mode is disabled
R/W-0
R/W-1
FLTSRC<4:0>
W = Writable bit
‘1’ = Bit is set
R/W-0
R/W-1
CLSRC<4:0>
R/W-0
R/W-1
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
R/W-1
(2)
FLTPOL
R/W-0
R/W-0
(2)
x = Bit is unknown
CLPOL
R/W-0
R/W-0
FLTMOD<1:0>
(1)
(2)
DS70657F-page 243
CLMOD
R/W-0
R/W-0
bit 8
bit 0