DSPIC33EP128MC504-I/ML Microchip Technology, DSPIC33EP128MC504-I/ML Datasheet - Page 494

• Manufacturer Part Number: DSPIC33EP128MC504-I/ML
• Description: Digital Signal Processors & Controllers - DSP, DSC 16B 128KB FL 16KBR 60MHz 44P OpAmps
• Manufacturer: Microchip Technology
• Type: dsPIC33E/PIC24Er

Specifications of DSPIC33EP128MC504-I/ML

• Rohs: yes
• Core: dsPIC33E
• Data Bus Width: 16 bit
• Program Memory Size: 128 KB
• Data Ram Size: 16 KB
• Maximum Clock Frequency: 7.37 MHz, 32 kHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5 x 16-bit, 2 x 32-bit
• Device Million Instructions Per Second: 70 MIPs
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Package / Case: TQFP-44
• Mounting Style: SMD/SMT
• Family / Core: dsPIC33E/PIC24E
• Interface Type: CAN, I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• On-chip Adc: Yes
• Product: DSPs
• Program Memory Type: Flash
• Supply Current: 10 mA

dsPIC33EPXXXGP50X, dsPIC33EPXXXMC20X/50X, AND PIC24EPXXXGP/MC20X
TABLE A-2:
DS70657F-page 494
Section 16.0 “High-Speed
PWM Module
(dsPIC33EPXXXMC20X/50X
and PIC24EPXXXMC20X
Devices Only)”
Section 21.0 “Enhanced
CAN (ECAN™) Module
(dsPIC33EPXXXGP/MC50X
Devices Only)”
Section 22.0 “Charge Time
Measurement Unit (CTMU)”
Section 25.0 “Op amp/
Comparator Module”
Section 27.0 “Special
Features”
Section 30.0 “Electrical
Characteristics”
Section Name
MAJOR SECTION UPDATES (CONTINUED)
Updated the High-Speed PWM Module Register Interconnection Diagram (see
Figure 16-2).
Added the TRGCONx and TRIGx registers (see Register 16-12 and Register 16-14,
respectively).
Updated the CANCKS bit value definitions in CiCTRL1: ECAN Control Register 1
(see Register 21-1).
Updated the IRNG<1:0> bit value definitions and added Note 2 in the CTMU Current
Control Register (see Register 22-3).
Updated the Op amp/Comparator I/O Operating Modes Diagram (see Figure 25-1).
Updated the User-programmable Blanking Function Block Diagram (see Figure 25-3).
Updated the Digital Filter Interconnect Block Diagram (see Figure 25-4).
Added Section 25.1 “Op amp Application Considerations”.
Added Note 2 to the Comparator Control Register (see Register 25-2).
Updated the bit definitions in the Comparator Mask Gating Control Register (see
Register 25-5).
Updated the FICD Configuration Register, updated Note 1, and added Note 3 in the
Configuration Byte Register Map (see Table 27-1).
Added Section 27.2 “User ID Words”.
Updated the following Absolute Maximum Ratings:
• Maximum current out of V
• Maximum current into V
Added Note 1 to the Operating MIPS vs. Voltage (see Table 30-1).
Updated all Idle Current (I
Table 30-7).
Updated all Doze Current (I
(see Table 30-9).
Added Note 2, removed parameter CM24, updated the Typical values parameters
CM10, CM20, CM21, CM32, CM41, CM44, and CM45, and updated the Minimum
values for CM40 and CM41, and the Maximum value for CM40 in the AC/DC
Characteristics: Op amp/Comparator (see Table 30-14).
Updated Note 2 and the Typical value for parameter VR310 in the Op amp/
Comparator Reference Voltage Settling Time Specifications (see Table 30-15).
Added Note 1, removed parameter VRD312, and added parameter VRD314 to the
Op amp/Comparator Voltage Reference DC Specifications (see Table 30-16).
Updated the Minimum, Typical, and Maximum values for Internal LPRC Accuracy
(see Table 30-22).
Updated the Minimum, Typical, and Maximum values for parameter SY37 in the
Reset, Watchdog Timer, Oscillator Start-up Timer, Power-up Timer Timing
Requirements (see Table 30-24).
The Maximum Data Rate values were updated for the SPI2 Maximum Data/Clock
Rate Summary (see Table 30-35)
IDLE
DD
DOZE
SS
pin
) Typical and Maximum DC Characteristics values (see
pin
Update Description
) Typical and Maximum DC Characteristics values
 2011-2012 Microchip Technology Inc.