C8051F021-GQ Silicon Laboratories Inc, C8051F021-GQ Datasheet - Page 135

IC 8051 MCU 64K FLASH 64TQFP

C8051F021-GQ

Manufacturer Part Number
C8051F021-GQ
Description
IC 8051 MCU 64K FLASH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Datasheets

Specifications of C8051F021-GQ

Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
64-TQFP, 64-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
32
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
32
Number Of Timers
4
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F020DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 8-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
32
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
5
No. Of Pwm Channels
5
Rohs Compliant
Yes
Data Rom Size
64 KB
A/d Bit Size
12 bit
A/d Channels Available
8
Height
1.05 mm
Length
10 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Width
10 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1200 - DEV KIT FOR F020/F021/F022/F023
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1201
14.
Each MCU includes an internal oscillator and an external oscillator drive circuit, either of which can generate the sys-
tem clock. The MCUs operate from the internal oscillator after any reset. This internal oscillator can be enabled/dis-
abled and its frequency can be set using the Internal Oscillator Control Register (OSCICN) as shown in Figure 14.1.
The internal oscillator's electrical specifications are given in Table 14.1.
Both oscillators are disabled when the /RST pin is held low. The MCUs can run from the internal oscillator perma-
nently, or can switch to the external oscillator if desired using CLKSL bit in the OSCICN Register. The external oscil-
lator requires an external resonator, crystal, capacitor, or RC network connected to the XTAL1/XTAL2 pins (see
Table 14.1). The oscillator circuit must be configured for one of these sources in the OSCXCN register. An external
CMOS clock can also provide the system clock; in this configuration, the XTAL1 pin is used as the CMOS clock
input. The XTAL1 and XTAL2 pins are NOT 5V tolerant.
OSCILLATORS
opt. 4
XTAL1
opt. 3
XTAL1
XTAL2
AV+
opt. 2
XTAL1
Figure 14.1. Oscillator Diagram
opt. 1
XTAL1
XTAL2
AGND
Rev. 1.4
VDD
AV+
Circuit
Input
OSCXCN
Internal Clock
OSCICN
Generator
EN
OSC
C8051F020/1/2/3
SYSCLK
135

Related parts for C8051F021-GQ