C8051F021-GQ Silicon Laboratories Inc, C8051F021-GQ Datasheet - Page 218

IC 8051 MCU 64K FLASH 64TQFP

C8051F021-GQ

Manufacturer Part Number
C8051F021-GQ
Description
IC 8051 MCU 64K FLASH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Datasheets

Specifications of C8051F021-GQ

Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
64-TQFP, 64-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
32
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
32
Number Of Timers
4
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F020DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 8-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
32
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
5
No. Of Pwm Channels
5
Rohs Compliant
Yes
Data Rom Size
64 KB
A/d Bit Size
12 bit
A/d Channels Available
8
Height
1.05 mm
Length
10 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Width
10 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1200 - DEV KIT FOR F020/F021/F022/F023
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1201
C8051F020/1/2/3
21.1.3. Mode 2: 9-Bit UART, Fixed Baud Rate
Mode 2 provides asynchronous, full-duplex communication using a total of eleven bits per data byte: a start bit, 8 data
bits (LSB first), a programmable ninth data bit, and a stop bit. Mode 2 supports multiprocessor communications and
hardware address recognition (see
the ninth data bit is determined by the value in TB81 (SCON1.3). It can be assigned the value of the parity flag P in
the PSW or used in multiprocessor communications. On receive, the ninth data bit goes into RB81 (SCON1.2) and
the stop bit is ignored.
Data transmission begins when an instruction writes a data byte to the SBUF1 register. The TI1 Transmit Interrupt
Flag (SCON1.1) is set at the end of the transmission (the beginning of the stop-bit time). Data reception can begin
any time after the REN1 Receive Enable bit (SCON1.4) is set to logic 1. After the stop bit is received, the data byte
will be loaded into the SBUF1 receive register if RI1 is logic 0 and one of the following requirements are met:
If the above conditions are satisfied, the eight bits of data are stored in SBUF1, the ninth bit is stored in RB81 and the
RI1 flag is set. If these conditions are not met, SBUF1 and RB81 will not be loaded and the RI1 flag will not be set.
An interrupt will occur if enabled when either TI1 or RI1 is set.
The baud rate in Mode 2 is either SYSCLK / 32 or SYSCLK / 64, depending on the value of the SMOD1 bit in regis-
ter PCON.
218
SPACE
MARK
BIT TIMES
BIT SAMPLING
1.
2.
SM21 is logic 0
SM21 is logic 1, the received 9th bit is logic 1, and the received address matches the UART1 address as
described in
START
BIT
Figure 21.5. UART Modes 2 and 3 Timing Diagram
Section
D0
21.2.
D1
Section “21.2. Multiprocessor Communications” on page
BaudRate
Equation 21.3. Mode 2 Baud Rate
D2
=
D3
2
Rev. 1.4
SMOD1
D4
SYSCLK
--------------------- -
D5
64
D6
D7
220). On transmit,
D8
STOP
BIT

Related parts for C8051F021-GQ