R5F21324ANSP#U1 Renesas Electronics America, R5F21324ANSP#U1 Datasheet - Page 234

• Manufacturer Part Number: R5F21324ANSP#U1
• Description: MCU 1KB FLASH 16K ROM 20-LSSOP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/32Ar

Specifications of R5F21324ANSP#U1

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 20-LSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Under development
R8C/32A Group
REJ09B0458-0020 Rev.0.20
Page 204 of 583
17.8
• Timer RA stops counting after a reset. Set the values in the timer RA and timer RA prescalers before the count
• Even if the prescaler and timer RA are read out in 16-bit units, these registers are read 1 byte at a time by the
• In pulse period measurement mode, bits TEDGF and TUNDF in the TRACR register can be set to 0 by writing 0
• When changing to pulse period measurement mode from another mode, the contents of bits TEDGF and TUNDF
• The TEDGF bit may be set to 1 by the first timer RA prescaler underflow generated after the count starts.
• When using the pulse period measurement mode, leave two or more periods of the timer RA prescaler
• The TCSTF bit retains 0 (count stops) for 0 to 1 cycle of the count source after setting the TSTART bit to 1 (count
• When the TRAPRE register is continuously written during count operation (TCSTF bit is set to 1), allow three or
• When the TRA register is continuously written during count operation (TCSTF bit is set to 1), allow three or
starts.
MCU. Consequently, the timer value may be updated during the period when these two registers are being read.
to these bits by a program. However, these bits remain unchanged if 1 is written. When using the READ-
MODIFY-WRITE instruction for the TRACR register, the TEDGF or TUNDF bit may be set to 0 although these
bits are set to 1 while the instruction is being executed. In this case, write 1 to the TEDGF or TUNDF bit which is
not supposed to be set to 0 with the MOV instruction.
are undefined. Write 0 to bits TEDGF and TUNDF before the count starts.
immediately after the count starts, then set the TEDGF bit to 0.
starts) while the count is stopped.
During this time, do not access registers associated with timer RA
counting at the first valid edge of the count source after The TCSTF bit is set to 1 (during count).
The TCSTF bit remains 1 for 0 to 1 cycle of the count source after setting the TSTART bit to 0 (count stops)
while the count is in progress. Timer RA counting is stopped when the TCSTF bit is set to 0.
During this time, do not access registers associated with timer RA
Note:
more cycles of the count source clock for each write interval.
more cycles of the prescaler underflow for each write interval.
1. Registers associated with timer RA: TRACR, TRAIOC, TRAMR, TRAPRE, and TRA.
Notes on Timer RA
Preliminary specification
Specifications in this manual are tentative and subject to change.
Nov 05, 2008
(1)
(1)
other than the TCSTF bit.
other than the TCSTF bit. Timer RA starts
17. Timer RA