R5F21324ANSP#U1 Renesas Electronics America, R5F21324ANSP#U1 Datasheet - Page 521

• Manufacturer Part Number: R5F21324ANSP#U1
• Description: MCU 1KB FLASH 16K ROM 20-LSSOP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/32Ar

Specifications of R5F21324ANSP#U1

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 20-LSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Under development
R8C/32A Group
REJ09B0458-0020 Rev.0.20
Page 491 of 583
30.4
Table 30.3
Operating mode
Rewrite control program
allocatable area
Rewrite control program
executable areas
Rewritable area
Software command
restrictions
Mode after programming or
block erasure or after
entering erase-suspend
CPU state during
programming and
block erasure
Flash memory
status detection
Conditions for entering
program-suspend
CPU clock
In CPU rewrite mode, the user ROM area can be rewritten by executing software commands from the CPU.
Therefore, the user ROM area can be rewritten directly while the MCU is mounted on a board without using a
ROM programmer. Execute the software command only to blocks in the user ROM area.
The flash module has an erase-suspend function which halts the erase operation temporarily during an erase
operation in CPU rewrite mode. During erase-suspend, the user ROM area can be read by a program.
Erase-write 0 mode (EW0 mode) and erase-write 1 mode (EW1 mode) are available in CPU rewrite mode.
Table 30.3 lists the Differences between EW0 Mode and EW1 Mode.
CPU Rewrite Mode
Item
Preliminary specification
Specifications in this manual are tentative and subject to change.
Differences between EW0 Mode and EW1 Mode
Single-chip mode
User ROM
RAM (The rewrite control program must
be transferred before being executed.)
However, the program can be executed
in the program ROM area when rewriting
the data flash area.
User ROM
—
Read array mode
The CPU operates.
Read bits FST7, FMT5, and FMT4 in
the FST register by a program.
• Set bits FMR20 and FMR21 in the
• Set bits FMR20 and FMR22 in the
20 MHz
Nov 05, 2008
FMR2 register to 1 by a program.
FMR2 register to 1 and the enabled
maskable interrupt is generated.
EW0 Mode
Single-chip mode
User ROM
User ROM or RAM
User ROM
Program and block erase commands
cannot be executed to any block which
contains the rewrite control program.
Read array mode
• The CPU operates while the data flash
• The CPU is put in a hold state while the
Read bits FST7, FMT5, and FMT4 in
the FST register by a program.
• Set bits FMR20 and FMR21 in the FMR2
• Set bits FMR20 and FMR22 in the FMR2
20 MHz
area is being programmed or block
erased.
program ROM area is being programmed
or block erased. (I/O ports retain the state
before the command execution).
register to 1 by a program (while rewriting
the data flash area).
register to 1 and the enabled maskable
interrupt is generated.
However, blocks which contain the
rewrite control program are excluded.
EW1 Mode
30. Flash Memory