R5F21324ANSP#U1 Renesas Electronics America, R5F21324ANSP#U1 Datasheet - Page 514

• Manufacturer Part Number: R5F21324ANSP#U1
• Description: MCU 1KB FLASH 16K ROM 20-LSSOP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/32Ar

Specifications of R5F21324ANSP#U1

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 15
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 20-LSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Under development
R8C/32A Group
REJ09B0458-0020 Rev.0.20
Page 484 of 583
29.3
Figure 29.2
Table 29.3
i = 1 or 3
1
2
3
4
5
6
Step
Comparator B1 and comparator B3 operate independently. Their operations are the same.
Table 29.3 lists the Procedure for Setting Registers Associated with Comparator B.
Figure 29.2 shows an Operating Example of Comparator Bi (i = 1 or 3).
If the analog input voltage is higher than the reference input voltage, the INTiCOUT bit in the INTCMP register is
set to 1. If the analog input voltage is lower than the reference input voltage, the INTiCOUT bit is set to 0. To use
the comparator Bi interrupt, set the INTiEN bit in the INTEN register to 1 (interrupt enabled). If the comparison
result changes at this time, a comparator Bi interrupt request is generated. Refer to 29.4 Comparator B1 and
Comparator B3 Interrupts for details of interrupts.
Select the function of pins IVCMPi and IVREFi. Refer to 7.5 Port Settings.
However, set registers and bits other than listed in step 2 and the following steps.
INTF
INTCMP
Wait for comparator stability time (100 µs max.)
INTEN
INTiIC
Reference input voltage
INTCMP register
Functional Description
INTiCOUT bit in
Register
Analog input voltage (V)
INTiIC register
IR bit in
Preliminary specification
Specifications in this manual are tentative and subject to change.
Procedure for Setting Registers Associated with Comparator B
Operating Example of Comparator Bi (i = 1 or 3)
The above applies when:
Bits INTiF1 to INTiF0 in INTF register = 00b (no filter)
INTiPL bit in the INTEN register = 0 (both edges)
i = 1 or 3
Select whether to enable or disable the filter.
Select the sampling clock.
INTiCP0
INTiEN
INTiPL
ILVL2 to ILVL0
IR
1
0
1
0
0
Bit
Nov 05, 2008
1 (operation enabled)
When using an interrupt: 1 (interrupt enabled)
When using an interrupt: Select the input polarity.
When using an interrupt: Select the interrupt priority level.
When using an interrupt: 0 (no interrupt requested: initialization)
Set to 0 by a program.
Setting Value
29. Comparator B