MC68EN360CAI25L Freescale Semiconductor, MC68EN360CAI25L Datasheet - Page 758

• Manufacturer Part Number: MC68EN360CAI25L
• Description: IC MPU QUICC 25MHZ 240-FQFP
• Manufacturer: Freescale Semiconductor
• Series: MC68000r

Specifications of MC68EN360CAI25L

• Processor Type: M683xx 32-Bit
• Speed: 25MHz
• Voltage: 5V
• Mounting Type: Surface Mount
• Package / Case: 240-FQFP
• Core Size: 32 Bit
• Cpu Speed: 25MHz
• Embedded Interface Type: SCP, TDM
• Digital Ic Case Style: FQFP
• No. Of Pins: 240
• Supply Voltage Range: 4.75V To 5.25V
• Rohs Compliant: Yes
• Family Name: M68xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 25MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 5V
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (min): 4.75V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 240
• Package Type: FQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Compliant

Applications
dled differently. See 9.4.2 Memory Interfaces.) To provide dynamic bus sizing, the MC68150
device may be added to the design shown here.
Parity is supported for both SRAM and DRAM arrays using the four-byte parity lines
PRTY3–PRTY0. When a parity error occurs, the error indication on the PERR pin causes
the QUICC to generate a level 5 interrupt to the MC68EC040. (Level 7 has already been
used for the breakpoint generation interrupt.) The parity error timing is not fast enough to
allow an MC68EC040 bus error to be generated on the bus cycle that generated a parity
error.
The QUICC supports MC68EC040 bursting using the BADD3–BADD2 pins. These pins nor-
mally reflect the values on A3–A2, but, in the case of a burst, are used to increment the
address to the memory array. If the memory devices already support MC68EC040 bursting
internally, the BADD3–BADD2 pins are not required.
The DRAM arrays require the four CAS3–CAS0 pins. Also, since an external address mul-
tiplexer is used, the AMUX pin is required to select between rows and columns. If, however,
the user's configuration does not require DRAM, the AMUX pin can be used as an OE pin
instead. This would save an inverter in a number of memory arrays.
The QUICC also provides four write enable (WEx) pins to select the correct byte during write
operations.
9.4.2.2 REGULAR EPROM. Figure 9-9 shows the glueless interface to standard EPROM
in the system. The assumption is made that only the MC68EC040 will access this array. No
bursting capability is used. The CONFIG2–CONFIG0 pins are configured to initialize the
system to slave mode, CS0 operating on a 32-bit port at reset, the MBAR at its normal loca-
tion, and MC68040 companion mode.
It would have been possible to use 16-bit-wide EPROM to reduce the chip count, if desired.
(See 9.4.2.3 Burst EPROM. for an example.)
9.4.2.3 BURST EPROM. Figure 9-10 shows the glueless interface to two burst EPROMs
available from National Semiconductor. These devices support a glueless interface to the
MC68040. In this design, the assumption is made that only the MC68EC040 will access this
array.
9-38
Many memory arrays show an inverter on the R/W pin to create
the OE signal. When using multiple memory arrays, it is possible
to share one inverter between multiple memory arrays; however,
this configuration is not shown.
Freescale Semiconductor, Inc.
For More Information On This Product,
MC68360 USER’S MANUAL
Go to: www.freescale.com
NOTE