PIC18F-LF1XK50 MICROCHIP [Microchip Technology], PIC18F-LF1XK50 Datasheet - Page 117

no-image

PIC18F-LF1XK50

Manufacturer Part Number
PIC18F-LF1XK50
Description
20-Pin USB Flash Microcontrollers
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
14.0
PIC18F/LF1XK50
(Capture/Compare/PWM)
contains a 16-bit register which can operate as a 16-bit
Capture register, a 16-bit Compare register or a PWM
Master/Slave Duty Cycle register.
REGISTER 14-1:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-4
bit 3-0
R/W-0
P1M1
ENHANCED
CAPTURE/COMPARE/PWM
(ECCP) MODULE
P1M<1:0>: Enhanced PWM Output Configuration bits
If CCP1M<3:2> = 00, 01, 10:
xx = P1A assigned as Capture/Compare input/output; P1B, P1C, P1D assigned as port pins
If CCP1M<3:2> = 11:
00 = Single output: P1A, P1B, P1C and P1D controlled by steering (See
01 = Full-bridge output forward: P1D modulated; P1A active; P1B, P1C inactive
10 = Half-bridge output: P1A, P1B modulated with dead-band control; P1C, P1D assigned as port pins
11 = Full-bridge output reverse: P1B modulated; P1C active; P1A, P1D inactive
DC1B<1:0>: PWM Duty Cycle bit 1 and bit 0
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found in
CCPR1L.
CCP1M<3:0>: Enhanced CCP Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCP module)
0001 = Reserved
0010 = Compare mode, toggle output on match
0011 = Reserved
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, initialize CCP1 pin low, set output on compare match (set CCP1IF)
1001 = Compare mode, initialize CCP1 pin high, clear output on compare match (set CCP1IF)
1010 = Compare mode, generate software interrupt only, CCP1 pin reverts to I/O state
1011 = Compare mode, trigger special event (ECCP resets TMR1 or TMR3, start A/D conversion, sets
1100 = PWM mode; P1A, P1C active-high; P1B, P1D active-high
1101 = PWM mode; P1A, P1C active-high; P1B, P1D active-low
1110 = PWM mode; P1A, P1C active-low; P1B, P1D active-high
1111 = PWM mode; P1A, P1C active-low; P1B, P1D active-low
R/W-0
P1M0
devices
Mode”).
CCP1CON: ENHANCED CAPTURE/COMPARE/PWM CONTROL REGISTER
CC1IF bit)
module.
W = Writable bit
‘1’ = Bit is set
have
DC1B1
R/W-0
The
one
module
ECCP
DC1B0
R/W-0
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
CCP1M3
R/W-0
CCP1 is implemented as a standard CCP module with
enhanced PWM capabilities. These include:
• Provision for 2 or 4 output channels
• Output steering
• Programmable polarity
• Programmable dead-band control
• Automatic shutdown and restart.
The enhanced features are discussed in detail in
Section 14.4 “PWM (Enhanced
PIC18F/LF1XK50
CCP1M2
R/W-0
Section 14.4.7 “Pulse Steering
x = Bit is unknown
CCP1M1
R/W-0
Mode)”.
DS41350E-page 117
CCP1M0
R/W-0
bit 0

Related parts for PIC18F-LF1XK50