AT89LP6440-20JU Atmel, AT89LP6440-20JU Datasheet - Page 81

• Manufacturer Part Number: AT89LP6440-20JU
• Description: MCU 8051 64K FLASH ISP 44PLCC
• Manufacturer: Atmel
• Series: 89LPr

Specifications of AT89LP6440-20JU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 8K x 8
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 38
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 13-14. Multi-Phasic PWM Modes
14. External Interrupts
3706A–MICRO–9/09
PHSD
PHSD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
The INT0 (P3.2) and INT1 (P3.3) pins of the AT89LP6440 may be used as external interrupt
sources. The external interrupts can be programmed to be level-activated or transition-activated
by setting or clearing bit IT1 or IT0 in Register TCON. If ITx = 0, external interrupt x is triggered
by a detected low at the INTx pin. If ITx = 1, external interrupt x is edge-triggered. In this mode if
successive samples of the INTx pin show a high in one cycle and a low in the next cycle, inter-
rupt request flag IEx in TCON is set. Flag bit IEx then requests the interrupt. Since the external
interrupt pins are sampled once each clock cycle, an input high or low should hold for at least 2
oscillator periods to ensure sampling. If the external interrupt is transition-activated, the external
source has to hold the request pin high for at least two clock cycles, and then hold it low for at
least two clock cycles to ensure that the transition is seen so that interrupt request flag IEx will
be set. IEx will be automatically cleared by the CPU when the service routine is called if gener-
ated in edge-triggered mode. If the external interrupt is level-activated, the external source has
to hold the request active until the requested interrupt is actually generated. Then the external
source must deactivate the request before the interrupt service routine is completed, or else
PHS = 000B
PHS = 001B
PHS = 010B
PHS = 011B
PHS = 100B
AT89LP6440 - Preliminary
81