MPC8533EVTARJA Freescale Semiconductor, MPC8533EVTARJA Datasheet - Page 891

• Manufacturer Part Number: MPC8533EVTARJA
• Description: MPU POWERQUICC 783-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8533EVTARJA

• Processor Type: MPC85xx PowerQUICC III 32-Bit
• Speed: 1.067GHz
• Voltage: 0.95 V ~ 1.05 V
• Mounting Type: Surface Mount
• Package / Case: 783-BBGA, FCBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -

The contents of the Rx FCB are defined in
Freescale Semiconductor
Bytes
0–1
0–1
12–13
14–15
8–11
Bits
0
1
2
3
4
5
6
7
MPC8533E PowerQUICC III Integrated Host Processor Family Reference Manual, Rev. 1
Name
CTU
PER
VLN
TUP
ETU
CIP
EIP
IP6
IP
—
—
VLAN tag recognized. This bit is set only if RCTRL[VLEX] is set.
0 No VLAN tag recognized.
1 IEEE Std. 802.1Q VLAN tag found; VLAN control word in VLCTL is valid.
IP header found at layer 3.RCTRL[PRSDEP] must be set to 10 or 11 in order to enable IP
discovery. See also IP6 bit of FCB.
0 No layer 3 header recognized.
1 An IP header was recognized at layer 3; the IANA protocol identifier for the next header can be
If S/W is relying on the RxFCB for the parse results, any RxFCB[IP] bits set with the corresponding
RxFCB[PRO] = 0xFF indicates a fragmented packet (or that this packet had a back-to-back IPv6
routing extension header). Additionally, RQFPR[IPF] (see
Filer Table Property Register
IP version 6 header found at layer 3.
0 No IPv6 header was found.
1 The layer 3 header was an IPv6 header provided IP = 1.
TCP or UDP header found at layer 4. RCTRL[PRSDEP] must be set to 10 or 11 in order to enable
TCP/UDP discovery.
0 No layer 4 header recognized.
1 The layer 4 header was recognized as either TCP (PRO = 0x06) or UDP (PRO = 0x11).
IPv4 header checksum checked. RCTRL[PRSDEP] must be set to 10 or 11 in order to enable IPv4
checksum verification.
0 IPv4 header checksum not verified, either because verification was disabled or a valid IPv4
1 IPv4 header checksum was verified by the eTSEC, and bit EIP indicates result.
TCP or UDP header checksum checked. RCTRL[PRSDEP] must be set to 11 in order to enable
layer 4 checksum verification.
0 TCP or UDP header checksum not verified, either because verification was disabled or a valid
1 TCP or UDP header checksum was verified by the eTSEC, and ETU indicates result.
IPv4 header checksum verification error. Not valid unless CIP = 1.
0 No checksum error in IPv4 header.
1 Error in header checksum only if IP = 1 and IP6 = 0.
TCP or UDP header checksum verification error. Not valid unless CTU = 1.
0 No checksum error in TCP or UDP header.
1 Error in header checksum only if PRO = 0x06 or PRO = 0x11.
Reserved
Parse error.
00 No error in L2 to L4 parse
01 Reserved
10 Inconsistent or unsupported L3 header sequence
11 Reserved
Reserved
found in PRO; see PRO for more information.
header could not be located.
TCP or UDP header could not be located. If a UDP header with zero checksum was located,
this bit is cleared in accordance with RFC 768.
Table 15-140. Rx Frame Control Block Descriptions
Table
(RQFPR)”) indicates that the packet was fragmented.
15-140.
Description
Enhanced Three-Speed Ethernet Controllers
Section 15.5.3.3.8, “Receive Queue
15-161