IRCC2.0 SMSC Corporation, IRCC2.0 Datasheet - Page 50
IRCC2.0
Manufacturer Part Number
IRCC2.0
Description
Infrared Communications Controller
Manufacturer
SMSC Corporation
Datasheet
1.IRCC2.0.pdf
(87 pages)
- Current page: 50 of 87
- Download datasheet (505Kb)
as a zero bit (Spacing level). The FE is reset to a
logic "0" whenever the Line Status Register is
read. In the FIFO mode this error is associated
with the particular character in the FIFO it applies
to. This error is indicated when the associated
character is at the top of the FIFO. The Serial Port
will try to resynchronize after a framing error. To
do this, it assumes that the framing error was due
to the next start bit, so it samples this 'start' bit
twice and then takes in the 'data'.
Bit 4
Break Interrupt (BI). Bit 4 is set to a logic "1"
whenever the received data input is held in the
Spacing state (logic "0") for longer than a full word
transmission time (that is, the total time of the start
bit + data bits + parity bits + stop bits). The BI is
reset after the CPU reads the contents of the Line
Status Register. In the FIFO mode this error is
associated with the particular character in the
FIFO it applies to. This error is indicated when the
associated character is at the top of the FIFO.
When break occurs only one zero character is
loaded into the FIFO. Restarting after a break is
received, requires the serial data (RXD) to be logic
"1" for at least 1/2 bit time.
Note: Bits 1 through 4 are the error conditions that
produce
whenever any of the corresponding conditions are
detected and the interrupt is enabled.
a
Receiver
Line
Status
Interrupt
50
Bit 5
Transmitter Holding Register Empty (THRE). Bit 5
indicates that the Serial Port is ready to accept a
new character for transmission. In addition, this bit
causes the Serial Port to issue an interrupt when
the Transmitter Holding Register interrupt enable
is set high. The THRE bit is set to a logic "1" when
a character is transferred from the Transmitter
Holding Register into the Transmitter Shift
Register. The bit is reset to logic "0" whenever the
CPU loads the Transmitter Holding Register. In
the FIFO mode this bit is set when the XMIT FIFO
is empty, it is cleared when at least 1 byte is
written to the XMIT FIFO. Bit 5 is a read only bit.
Bit 6
Transmitter Empty (TEMT). Bit 6 is set to a logic
"1" whenever the Transmitter Holding Register
(THR) and Transmitter Shift Register (TSR) are
both empty. It is reset to logic "0" whenever either
the THR or TSR contains a data character. Bit 6
is a read only bit. In the FIFO mode this bit is set
whenever the THR and TSR are both empty,
Bit 7
This bit is permanently set to logic "0" in the 450
mode. In the FIFO mode, this bit is set to a logic
"1" when there is at least one parity error, framing
error or break indication in the FIFO. This bit is
cleared when the LSR is read if there are no
subsequent errors in the FIFO.
MODEM STATUS REGISTER (MSR)
Address Offset = 6H, DLAB = X, READ/ WRITE
This 8 bit register provides the current state of the
control lines from the MODEM (or peripheral
device).
information, four bits of the MODEM Status
Register (MSR)
In addition to this current state
provide change information.
Related parts for IRCC2.0
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INFRARED COMMUNICATIONS CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
IR-EMPFANGER/DEMODULATOR-BAUSTEIN / IR-RECEIVER/DEMODULATOR DEVICE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
IR-Empfanger fur Fernbedienungen fur kurze Burst IR-Receiver for Remote Control Systems for Short Burst
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Ir-empfanger/demodulator-baustein, Ir-receiver/demodulator Device
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
IR-EMPFANGER/DEMODULATOR-BAUSTEIN, IR-RECEIVER/DEMODULATOR DEVICE
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IR-Empfanger fur Fernbedienungen fur kurze Burst IR-Receiver for Remote Control Systems for Short Burst
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
Part Number:
Description:
IR-Empfanger fur Fernbedienungen IR-Receiver for Remote Control Systems Lead (Pb) Free Product - RoHS Compliant
Manufacturer:
OSRAM [OSRAM GmbH]
Datasheet:
Part Number:
Description:
IR-Receiver for Remote Control Systems
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Ir-receiver For Remote Control Systems
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Ir-receiver For Remote Control Systems
Manufacturer:
Osram Opto Semiconductors
Datasheet:
Part Number:
Description:
IR-Lumineszenzdiode (850 nm) mit hoher Ausgangsleistung
Manufacturer:
OSRAM [OSRAM GmbH]
Datasheet:
Part Number:
Description:
IR-Lumineszenzdiode (850 nm) mit hoher Ausgangsleistung
Manufacturer:
OSRAM [OSRAM GmbH]
Datasheet:
Part Number:
Description:
IR-Lumineszenzdiode (940 nm) mit hoher Ausgangsleistung
Manufacturer:
OSRAM [OSRAM GmbH]
Datasheet:
Part Number:
Description:
IR-Lumineszenzdiode (950 nm) im TO-46-Geh®se Infrared Emitter (950 nm) in TO-46 Package Lead (Pb) Free Product - RoHS Compliant
Manufacturer:
OSRAM [OSRAM GmbH]
Datasheet:
Part Number:
Description:
IR-Lumineszenzdiode (880 nm) im TO-46-Gehäuse
Manufacturer:
OSRAM [OSRAM GmbH]
Datasheet: