LAN9220-ABZJ SMSC, LAN9220-ABZJ Datasheet - Page 26

• Manufacturer Part Number: LAN9220-ABZJ
• Description: Ethernet ICs 16Bit Single Chip Ethernet Controller
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9220-ABZJ

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Supply Current (max): 85 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 2.7 (03-15-10)
3.5
Setting the Wake-Up Frame Enable bit (WUEN) in the “WUCSR—Wake-up Control and Status
Register”, places the LAN9220 MAC in the wake-up frame detection mode. In this mode, normal data
reception is disabled, and detection logic within the MAC examines receive data for the pre-
programmed wake-up frame patterns. The LAN9220 can be programmed to notify the host of the
wake-up frame detection with the assertion of the host interrupt (IRQ) or assertion of the power
management event signal (PME). Upon detection, the Wake-Up Frame Received bit (WUFR) in the
WUCSR is set. When the host clears the WUEN bit the LAN9220 will resume normal receive operation.
Before putting the MAC into the wake-up frame detection state, the host must provide the detection
logic with a list of sample frames and their corresponding byte masks. This information is written into
the Wake-up Frame Filter register (WUFF). Please refer to
Filter," on page 115
The MAC supports four programmable filters that support many different receive packet patterns. If
remote wake-up mode is enabled, the remote wake-up function receives all frames addressed to the
MAC. It then checks each frame against the enabled filter and recognizes the frame as a remote wake-
up frame if it passes the wakeup frame filter register’s address filtering and CRC value match.
In order to determine which bytes of the frames should be checked by the CRC module, the MAC uses
a programmable byte mask and a programmable pattern offset for each of the four supported filters.
The pattern’s offset defines the location of the first byte that should be checked in the frame. Since
the destination address is checked by the address filtering Function, the pattern offset is always greater
than 12.
The byte mask is a 31-bit field that specifies whether or not each of the 31 contiguous bytes within
the frame, beginning in the pattern offset, should be checked. If bit j in the byte mask is set, the
detection logic checks byte offset +j in the frame. In order to load the Wake-up Frame Filter register,
the host LAN driver software must perform eight writes to the Wake-up Frame Filter register (WUFF).
The Diagram shown in
up frame filter register’s structure.
Note 3.1
Note 3.2
Note 3.3
Wake-up Frame Detection
Wake-up frame detection can be performed when the LAN9220 is in the D0 or D1 power
states. In the D0 state, wake-up frame detection is enabled when the WUEN bit is set.
Wake-up frame detection, as well as Magic Packet detection, is always enabled and
cannot be disabled when the device enters the D1 state.
When wake-up frame detection is enabled via the WUEN bit of the
Control and Status
the state of the Disable Broadcast Frame (BCAST) bit in the
Register.
for additional information on this register.
Table 3.2, "Wake-Up Frame Filter Register Structure"
16-bit Non-PCI Small Form Factor 10/100 Ethernet Controller with Variable Voltage I/O & HP Auto-MDIX Support
Register, a broadcast wake-up frame will wake-up the device despite
DATASHEET
26
Section 5.4.11, "WUFF—Wake-up Frame
MAC_CR—MAC Control
below, shows the wake-
WUCSR—Wake-up
SMSC LAN9220
Datasheet