LAN9220-ABZJ SMSC, LAN9220-ABZJ Datasheet - Page 78

• Manufacturer Part Number: LAN9220-ABZJ
• Description: Ethernet ICs 16Bit Single Chip Ethernet Controller
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9220-ABZJ

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Supply Current (max): 85 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 2.7 (03-15-10)
5.1
5.2
5.2.1
5.2.2
RO
WO
R/W
R/WC
RC
LL
LH
SC
NASR
Reserved
Bits
Reserved
Registers
Default
States
SYMBOL
The LAN9220 contains four host-accessible FIFOs: RX Status, RX Data, TX Status, and TX Data
FIFOs. The sizes Data FIFOs and the RX Status FIFO are configurable through the CSRs.
RX FIFO Ports
The RX Data Path contains two Read-Only FIFOs: RX Status and RX Data. The RX Status FIFO has
two ports at different address locations. The RX Status FIFO Port causes the top of the RX Status
FIFO to be “popped”, and is destructive. The RX Status FIFO PEEK Port allows the top of the RX
Status FIFO to be read without “popping” it.
The RX Data FIFO has a single port; reading data from this port always causes the top of the RX Data
FIFO to be “popped”. This port is aliased to 16 DWORD locations. The host may access the top of
the RX Data FIFO through any of these locations.
TX FIFO Ports
The TX Data Path consists of two FIFOs, TX Status and RX Data. The TX Status FIFO also has two
ports at different locations. When the TX Status FIFO Port is read, the top of the TX Status FIFO is
popped. When the TX Status FIFO PEEK Port is read, the top of the TX Status FIFO is not popped.
The TX data FIFO is Write Only. It is aliased to 16 DWORD locations. The host may access the top
of the TX Data FIFO through any of these locations.
Register Nomenclature and Access Attributes
RX and TX FIFO Ports
Read Only: If a register is read only, writes to this register have no effect.
Write Only: If a register is write only, reads always return 0.
Read/Write: A register with this attribute can be read and written
Read/Write Clear: A register bit with this attribute can be read and written. However, a write of a 1
clears (sets to 0) the corresponding bit and a write of a 0 has no effect.
Read to Clear: A register bit with this attribute is cleared when read.
Latch Low: Clear on read of register
Latch High: Clear on read of register
Self-Clearing
Not Affected by Software Reset
Certain bits within registers are listed as “Reserved”. Unless stated otherwise, these bits must be
written with zeros for future compatibility. The values of these bits are not guaranteed when read.
Certain configuration registers within the LAN9220 are listed as “Reserved”. These registers are not
guaranteed to return any particular value when read. These registers must not be written to or
modified by system failure; doing so could result in failure of the device and system.
At Reset - System reset or Software Reset - internal registers are set to their default states.
The default states provide a minimum level of functionality needed to successfully bring up a system,
but do not necessarily provide desired or optimal configuration of the device. It is the responsibility
of the system initialization software to properly determine the operating parameters and optional
system features that are applicable, and to program the LAN9220 registers accordingly.
16-bit Non-PCI Small Form Factor 10/100 Ethernet Controller with Variable Voltage I/O & HP Auto-MDIX Support
DATASHEET
78
DESCRIPTION
SMSC LAN9220
Datasheet