LAN9220-ABZJ SMSC, LAN9220-ABZJ Datasheet - Page 48

• Manufacturer Part Number: LAN9220-ABZJ
• Description: Ethernet ICs 16Bit Single Chip Ethernet Controller
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9220-ABZJ

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Supply Current (max): 85 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) after an internal
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) immediately. If
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) within 2 ms. If
APPLICATION NOTE: Under normal conditions, the READY bit in PMT_CTRL will be set (high -”1”) immediately,
Revision 2.7 (03-15-10)
3.11.1
3.11.2
3.11.3
3.11.4
3.11.4.1
3.11.4.2
3.12
Hardware Reset Input (nRESET)
A hardware reset will occur when the nRESET input signal is driven low. The READY bit in the
PMT_CTRL register can be read from the host interface, and will read back a ‘0’ until the hardware
reset is complete. Upon completion of the hardware reset, the READY bit in PMT_CTRL is set high.
After the “READY” bit is set, the LAN9220 can be configured via its control registers. The nRESET
signal is pulled-high internally by the LAN9220 and can be left unconnected if unused. If used,
nRESET must be driven low for a minimum period as defined in
page
Resume Reset Timing
After issuing a write to the BYTE_TEST register to wake the LAN9220 from a power-down state, the
READY bit in PMT_CTRL will assert (set High) within 2ms.
Soft Reset (SRST)
Soft reset is initiated by writing a ‘1’ to bit 0 of the HW_CFG register (SRST). This self-clearing bit will
return to ‘0’ after approximately 2 μs, at which time the Soft Reset is complete. Soft reset does not
clear control register bits marked as NASR. Following power-on, a soft reset must not be performed
until the READY bit in the PMT_CTRL register has been set.
PHY Reset Timing
The following sections specify the operation and time required for the internal PHY to become
operational after various resets or when returning from the reduced power state.
PHY Soft Reset via PMT_CTRL bit 10 (PHY_RST)
The PHY soft reset is initiated by writing a ‘1’ to bit 10 of the PMT_CTRL register (PHY_RST). This
self-clearing bit will return to ‘0’ after approximately 100 μs, at which time the PHY reset is complete.
PHY Soft Reset via PHY Basic Control Register (PHY Reg. 0.15)
The PHY Reg. 0.15 Soft Reset is initiated by writing a ‘1’ to bit 15 of the PHY’s Basic Control Register.
This self-clearing bit will return to ‘0’ at which time the PHY reset is complete.
Data is queued for transmission by writing it into the TX data FIFO. Each packet to be transmitted may
be divided among multiple buffers. Each buffer starts with a two DWORD TX command (TX command
TX Data Path Operation
137. If nRESET is unused, the device must be reset following power-up via a soft reset (SRST).
reset (22ms). If the software driver polls this bit and it is not set within 100ms, then an error
condition occurred.
the software driver polls this bit and it is not set within 100ms, then an error condition
occurred.
the software driver polls this bit and it is not set within 100ms, then an error condition
occurred.
(within 2μs). If the software driver polls this bit and it is not set within 100ms, then an error
condition occurred.
16-bit Non-PCI Small Form Factor 10/100 Ethernet Controller with Variable Voltage I/O & HP Auto-MDIX Support
DATASHEET
48
Section 6.10, "Reset Timing," on
SMSC LAN9220
Datasheet