20-668-0003 Rabbit Semiconductor, 20-668-0003 Datasheet - Page 86

• Manufacturer Part Number: 20-668-0003
• Description: IC CPU RABBIT2000 30MHZ 100PQFP
• Manufacturer: Rabbit Semiconductor

Specifications of 20-668-0003

• Processor Type: Rabbit 2000 8-Bit
• Speed: 30MHz
• Voltage: 2.7V, 3V, 3.3V, 5V
• Mounting Type: Surface Mount
• Package / Case: 100-MQFP, 100-PQFP
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 30 MHz
• Operating Supply Voltage: 0 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 40
• Number Of Timers: 8 & 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 20-668-0003; 316-1062

7.7 Watchdog Timer
The watchdog timer is a 17-bit counter. In normal operation it is driven by the 32.768 kHz
clock. When the watchdog timer reaches any of several values corresponding to a delay of
from 0.25 to 2 seconds, it “times out.” When it times out, it emits a 1-clock pulse from the
watchdog output pin and it resets the processor via an internal circuit. To prevent this tim-
eout, the program must “hit” the watchdog timer before it times out. The hit is accom-
plished by storing a code in WDTCR. Note that although a watchdog timeout resets the
processor, it does not reset the timeout period stored in the WDTCR. This was done inten-
tionally because an application may require the initialization of the processor resulting
from the watchdog timeout to be based on a specific timeout period that is different from
that of the reset initialization.
The watchdog timer may be disabled by storing a special code in the WDTTR register.
Normally this should not be done unless an external watchdog device is used. The purpose
of the watchdog is to unhang the processor from an endless loop caused by a software
crash or a hardware upset.
It is important to use extreme care in writing software to hit the watchdog timer (or to turn
off the watchdog timer). The programmer should not sprinkle instructions to hit the watch-
dog timer throughout his program because such instructions can become part of an endless
loop if the program crashes and thus disable the recovery ability given by having a watch-
dog.
The following is a suggested method for hitting the watchdog. An array of bytes is set up
in RAM. Each of these bytes is a virtual watchdog. To hit a virtual watchdog, a number is
stored in a byte. Every virtual watchdog is counted down by an interrupt routine driven by
a periodic interrupt. This can happen every 10 ms. If none of the virtual watchdogs has
counted down to zero, the interrupt routine hits the hardware watchdog. If any have
counted down to zero, the interrupt routine disables interrupts, and then enters an endless
loop waiting for the reset. Hits of the virtual watchdogs are placed in the user’s program at
“must exercise” locations.
80
7:0
Bit(s)
Table 7-8. Watchdog Timer Control Register (WDTCR adr = 0x08)
0x5A
0x57
0x59
0x53
other
Value
Restart (hit) the watchdog timer, with a 2-second timeout period.
Restart (hit) the watchdog timer, with a 1-second timeout period.
Restart (hit) the watchdog timer, with a 500 ms timeout period.
Restart (hit) the watchdog timer, with a 250 ms timeout period.
No effect on watchdog timer.
Description
Rabbit 2000 Microprocessor User’s Manual