SAM3A4C Atmel Corporation, SAM3A4C Datasheet - Page 218
SAM3A4C
Manufacturer Part Number
SAM3A4C
Description
Manufacturer
Atmel Corporation
- Current page: 218 of 1465
- Download datasheet (26Mb)
12.5
12.5.1
12.5.2
Figure 12-4. Debug Architecture
12.5.3
218
218
Functional Description
data address sampler
SAM3X/A
SAM3X/A
Test Pin
Debug Architecture
Serial Wire/JTAG Debug Port (SWJ-DP)
4 watchpoints
interrupt trace
data sampler
CPU statistics
PC sampler
DWT
One dedicated pin, TST, is used to define the device operating mode. When this pin is at low
level during power-up, the device is in normal operating mode. When at high level, the device is
in test mode or FFPI mode. The TST pin integrates a permanent pull-down resistor of about 15
k
low or high level at power up, it must remain in the same state during the duration of the whole
operation.
Figure 12-4
tional units for debug:
The debug architecture information that follows is mainly dedicated to developers of SWJ-DP
Emulators/Probes and debugging tool vendors for Cortex M3-based microcontrollers. For further
details on SWJ-DP see the Cortex M3 technical reference manual.
The Cortex-M3 embeds a SWJ-DP Debug port which is the standard CoreSight
combines Serial Wire Debug Port (SW-DP), from 2 to 3 pins and JTAG debug Port (JTAG-DP),
5 pins.
By default, the JTAG Debug Port is active. If the host debugger wants to switch to the Serial
Wire Debug Port, it must provide a dedicated JTAG sequence on TMS/SWDIO and
TCK/SWCLK which disables JTAG-DP and enables SW-DP.
• SWJ-DP (Serial Wire/JTAG Debug Port)
• FPB (Flash Patch Breakpoint)
• DWT (Data Watchpoint and Trace)
• ITM (Instrumentation Trace Macrocell)
• TPIU (Trace Port Interface Unit)
so that it can be left unconnected for normal operation. Note that when setting the TST pin to
shows the Debug Architecture used in the SAM3. The Cortex-M3 embeds four func-
software trace
time stamping
6 breakpoints
32 channels
FPB
ITM
TPIU
SWD/JTAG
SWO trace
SWJ-DP
11057A–ATARM–17-Feb-12
11057A–ATARM–17-Feb-12
™
debug port. It
Related parts for SAM3A4C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: