at91sam9263 ATMEL Corporation, at91sam9263 Datasheet - Page 13
at91sam9263
Manufacturer Part Number
at91sam9263
Description
At91 Arm Thumb Microcontrollers
Manufacturer
ATMEL Corporation
Datasheet
1.AT91SAM9263.pdf
(1065 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
at91sam9263-CJ
Manufacturer:
ATMEL
Quantity:
181
Company:
Part Number:
at91sam9263-EK
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
at91sam9263B-CU
Manufacturer:
IDT
Quantity:
1 043
Part Number:
at91sam9263B-CU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
at91sam9263B-CU-100
Manufacturer:
ATMEL
Quantity:
1 000
- Current page: 13 of 1065
- Download datasheet (16Mb)
5.2
5.3
6. I/O Line Considerations
6.1
6249D–ATARM–20-Dec-07
Power Consumption
Programmable I/O Lines Power Supplies
JTAG Port Pins
The power supplies VDDIOM0, VDDIOM1 and VDDIOP0, VDDIOP1 are identified in the pinout
table and the multiplexing tables. These supplies enable the user to power the device differently
for interfacing with memories and for interfacing with peripherals.
Ground pins GND are common to VDDOSC, VDDCORE, VDDIOM0, VDDIOM1, VDDIOP0 and
VDDIOP1 pins power supplies. Separated ground pins are provided for VDDBU and VDDPLL.
These ground pins are respectively GNDBU and GNDPLL.
The AT91SAM9263 consumes about 700 µA (worst case) of static current on VDDCORE at
25°C. This static current rises at up to 7 mA if the temperature increases to 85°C.
On VDDBU, the current does not exceed 3 µA @25°C, but can rise at up to 20 µA @85°C. An
automatic switch to VDDCORE guarantees low power consumption on the battery when the sys-
tem is on.
For dynamic power consumption, the AT91SAM9263 consumes a maximum of 70 mA on
VDDCORE at maximum conditions (1.2V, 25°C, processor running full-performance algorithm).
The power supply pins VDDIOM0 and VDDIOM1 accept two voltage ranges. This allows the
device to reach its maximum speed, either out of 1.8V or 3.0V external memories.
The maximum speed is 100 MHz on the pin SDCK (SDRAM Clock) loaded with 30 pF for power
supply at 1.8V and 50pF for power supply at 3.3V. The other signals (control, address and data
signals) do not go over 50MHz.
The voltage ranges are determined by programming registers in the Chip Configuration registers
located in the Matrix User Interface.
At reset, the selected voltage defaults to 3.3V nominal and power supply pins can accept either
1.8V or 3.3V. However, the device cannot reach its maximum speed if the voltage supplied to
the pins is only 1.8V without reprogramming the EBI0 voltage range. The user must be sure to
program the EBI0 voltage range before getting the device out of its Slow Clock Mode.
TMS, TDI and TCK are Schmitt trigger inputs and have no pull-up resistors.
TDO and RTCK are outputs, driven at up to VDDIOP0, and have no pull-up resistors.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level
(VDDBU). It integrates a permanent pull-down resistor of about 15 kΩ to GNDBU, so that it can
be left unconnected for normal operations.
• VDDBU pin: Powers the Slow Clock oscillator and a part of the System Controller; voltage
• VDDPLL pin: Powers the PLL cells; voltage ranges from 3.0V to 3.6V, 3.3V nominal.
• VDDOSC pin: Powers the Main Oscillator cells; voltage ranges from 3.0V to 3.6V, L3.3V
ranges from 1.08V to 1.32V, 1.2V nominal. During startup, backup voltage (VDDBU) slope
must be superior or equal to 5V/ms.
nominal.
AT91SAM9263 Preliminary
13
Related parts for at91sam9263
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
At91sam Arm-based Flash Mcu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Flash Mcu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
At91sam Arm-based Embedded Mpu
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 ARM Thumb-based Microcontrollers
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 ARM THUMB-BASED MICROCONTROLLERS
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 ARM Thumb-based Microcontrollers
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AT91 MEMORY EXTENSION CARD
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
AT91 ARM X40 SERIES EVAL KIT
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
AT91 ARM Cortex M3-based Processor
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
AT91 ARM Thumb-based Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet: