S912XET256J2VAGR Freescale Semiconductor, S912XET256J2VAGR Datasheet - Page 999

• Manufacturer Part Number: S912XET256J2VAGR
• Description: 16-bit Microcontrollers - MCU Watchdog OSC/Timer -40 C to + 105 C HCS12X MCU SPI
• Manufacturer: Freescale Semiconductor

Specifications of S912XET256J2VAGR

• Core: HCS12X
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 256 KB
• Data Ram Size: 16 KB
• On-chip Adc: Yes
• Package / Case: LQFP
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Interface Type: CAN, SCI, SPI
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 119
• Number Of Timers: 25
• Program Memory Type: Flash
• Supply Voltage - Max: 1.98 V, 2.9 V, 5.5 V
• Supply Voltage - Min: 1.72 V, 2.7 V, 3.13 V

state. During the execution of this command (CCIF=0) the user must not write to any Flash module
register. The CCIF flag is set after the Unsecure Flash operation has completed.
26.4.2.12 Verify Backdoor Access Key Command
The Verify Backdoor Access Key command will only execute if it is enabled by the KEYEN bits in the
FSEC register (see
supplied keys match those stored in the Flash security bytes of the Flash configuration field (see
3). The Verify Backdoor Access Key command must not be executed from the Flash block containing the
backdoor comparison key to avoid code runaway.
Upon clearing CCIF to launch the Verify Backdoor Access Key command, the Memory Controller will
check the FSEC KEYEN bits to verify that this command is enabled. If not enabled, the Memory
Controller sets the ACCERR bit in the FSTAT register and terminates. If the command is enabled, the
Memory Controller compares the key provided in FCCOB to the backdoor comparison key in the Flash
configuration field with Key 0 compared to 0x7F_FF00, etc. If the backdoor keys match, security will be
released. If the backdoor keys do not match, security is not released and all future attempts to execute the
Verify Backdoor Access Key command are aborted (set ACCERR) until a reset occurs. The CCIF flag is
set after the Verify Backdoor Access Key operation has completed.
Freescale Semiconductor
1. As found in the memory map for FTM512K3.
FERSTAT
Register
FSTAT
Table 26-55. Verify Backdoor Access Key Command FCCOB Requirements
Table
CCOBIX[2:0]
MGSTAT1
MGSTAT0
EPVIOLIF
ACCERR
Error Bit
FPVIOL
000
001
010
011
100
Table 26-54. Unsecure Flash Command Error Handling
26-11). The Verify Backdoor Access Key command releases security if user-
MC9S12XE-Family Reference Manual Rev. 1.25
Set if CCOBIX[2:0] != 000 at command launch
Set if a Load Data Field command sequence is currently active
Set if command not available in current mode (see
Set if any area of the P-Flash memory is protected
Set if any errors have been encountered during the verify operation
Set if any non-correctable errors have been encountered during the verify
operation
Set if any area of the buffer RAM EEE partition is protected
1
0x0C
FCCOB Parameters
Key 0
Key 1
Key 2
Key 3
Error Condition
Chapter 26 384 KByte Flash Module (S12XFTM384K2V1)
Not required
Table
26-30)
(1)
Table 26-
999