ST7FLITE35F2M6 STMicroelectronics, ST7FLITE35F2M6 Datasheet - Page 105

• Manufacturer Part Number: ST7FLITE35F2M6
• Description: IC MCU 8BIT 8K FLASH 20SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

}
/*-----------------------------------------------------------------------------
ROUTINE NAME : I2C_User_IT_Routine
INPUT
OUTPUT
DESCRIPTION : Control comes into this routine when an interrupt is generated.
COMMENTS
-----------------------------------------------------------------------------*/
#ifdef _HIWARE_
#pragma TRAP_PROC SAVE_REGS
#else
#ifdef _COSMIC_
@interrupt
}
/* Reception of set of data in the user buffer */
I2C_GetBuffer (Buff_Test,(unsigned char) 10);
/* Here, user can perform other tasks or operations except reception till
the time reception is complete, after which user can perform reception
again */
Timeoutcount = 0 ;
Temp2 = I2C_IsReceptionCompleted() ;
while ((User_Timeout_Function()) && ((Temp2) == I2C_RX_BUFFER_ONGOING))
{
}
/* To be sure that the communication by this point has been completed */
if (User_Timeout_Function())
{
}
#endif
User can use the I2C interrupt service routine function or he
can write his own code inside this routine at his own risk. The
data transfer syncronisation may be affected if user includes
his own code along with I2C ISR function.
: None
: None
: None
}
Temp2 = I2C_IsReceptionCompleted() ;
switch (Temp1)
{
}
default:
case I2C_RX_BERR:
case I2C_RX_BUFFER_ONGOING:
case I2C_DATA_RX_OK:
default:
Rx_Data =I2C_GetByte ();
break;
User_Function ();
break;
User_Function();
break;
break;
break;
/* If none of the above condition is true */
/* None of the above condition is true */
/* Additional registers will be saved */
/* Any data received before calling
/* Cosmic interrupt handling */
/* Test for HIWARE Compiler */
/* Test for Cosmic Compiler */
this function is ignored */
/* Reception successful */
Function Descriptions
/* Error Management */
105/235