ST7FLITE35F2M6 STMicroelectronics, ST7FLITE35F2M6 Datasheet - Page 110

• Manufacturer Part Number: ST7FLITE35F2M6
• Description: IC MCU 8BIT 8K FLASH 20SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Function Descriptions
Table 66. I2Cs_PutBuffer
Notes:
– This function is only for I2C_POLLING_TX mode.
– Here, an Acknowledge Failure (I2Cs_TX_AF) error is not returned as it is handled internally.
Caution: Control can be lost if I2C is disabled while using this function for I2C Polling mode.
Overflow condition: The overflow bytes neglected through dummy bytes (0xFF).
110/235
Function Name
Function Prototype
Behaviour Description
Input Parameter 1
Input Parameter 2
Output Parameters
Required Preconditions
Functions called
Postconditions
See also
* The maximum size of the buffer is under user control.
I2Cs_PutBuffer
I2Cs_ErrCode_t I2Cs_PutBuffer(unsigned char *PtrTo-
Buffer, unsigned char MaxSize)
Transmits data buffer from the user defined area for
I2C_POLLING_TX mode. The data transmission will dis-
continue, if any error occurs during transmission and the
error status will be returned.
*PtrToBuffer
Start address of the user buffer
MaxSize
The maximum no of bytes to be transmitted
I2Cs_BERR
An bus error has occurred
I2Cs_ADDRESS_DETECTED
If the device address is matched
I2Cs_GENERAL_CALL
If the general call is detected
I2Cs_TX_DATA_OK
If there is no error in data transmission and stop is detect-
ed correctly.
I2Cs_OVERFLOW_TX
If transmission has taken place correctly but the some
byte transmitted will be dummy bytes (0xFF). As the no of
bytes transmitted are more than the maximum size of the
buffer.
1. You must define I2C_POLLING_TX mode in
ST7lib_config.h
2. I2C communication mode must be detected through the
I2Cs_GetCommMode
None
None
I2Cs_GetBuffer, I2Cs_PutBuffer (I2C Interrupt driven
mode)