ST7FLITE35F2M6 STMicroelectronics, ST7FLITE35F2M6 Datasheet - Page 81

• Manufacturer Part Number: ST7FLITE35F2M6
• Description: IC MCU 8BIT 8K FLASH 20SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

9.1.4 I2C MASTER
Following are the functions related to both Single master and multi master I2C.
Note: If you select I2C Interrupt driven communication mode, interrupts must be enabled dur-
Function Name
Function Prototype
Behaviour Description
Input Parameters
Output Parameters
Required Preconditions
Functions called
Postconditions
See also
ing initialization.
I2C_Init
Void I2C_Init (I2C_Init_Param Init_Value)
Initialization of I2C. By default, I2C peripheral is enabled,
acknowledge and interrupts are disabled. If single master
I2C device is selected, I2C will be idle. You can change
the default configuration by selecting the input parameters
given below. You can pass one or more parameters by
logically ‘OR’ing them.
I2C_DEFAULT_PARAM1
Load all I2C registers with default value. Only I2C periph-
eral is enabled (PE bit is set).
I2C_ENABLE_ACK
Enables acknowledge.
I2C_IT_ENABLE
Enables interrupt
None
1. I/O port should be configured correctly.
2. If you want to configure single master I2C, the ST72F65
device must be selected.
None
1. If you want to enable interrupts, the I2C_IT_ENABLE
parameter has to be passed in the I2C_Init function. After
the I2C_Init function is called, you should use the Ena-
bleInterrupts macro to reset the Interrupt mask.
2. For single master I2C, to configure I2C in master mode,
you have to call I2C_Generate_Start after this function .
None
Function Descriptions
81/235