ST7FLITE35F2M6 STMicroelectronics, ST7FLITE35F2M6 Datasheet - Page 130

• Manufacturer Part Number: ST7FLITE35F2M6
• Description: IC MCU 8BIT 8K FLASH 20SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Function Descriptions
Table 82. TIMERx_OPM_Mode
Notes:
– The compare 1 flag can not be set by hardware but the compare interrupt can be generated
130/235
Function Name
Function Prototype
Behaviour Description
Input Parameter 1
Input Parameter 2
Input Parameter 3
Input Parameter 4
Output Parameter
Required Preconditions
Functions called.
Postconditions
See also
when the compare 2 flag is set.
1) Function not available in ST72F65.
TIMERx_OPM_Mode
Void TIMERx_OPM_Mode(Timer_Edge
EDGE_SELECT_Y,Timer_Olevel
OUTPUT1_L,Timer_Olevel OUTPUT2_L, unsigned int
OCR_VALUE)
Configures the timer in One Pulse Mode. It enables the
generation of a pulse when an external event occurs. If
both PWM and OPM modes are active then OPM will not
work. In OPM,OCMP1 cannot be used for output compare
only OCMP2 is available for output compare.
TIMER_EDGE_X
X = 0, input capture1 occurs at falling edge.
X = 1, input capture1 occurs at rising edge.
TIMER_OUTPUT1_F
Low level is reflected at the output compare1 pin after suc-
cessful comparison of output compare1 register with free
running counter.
TIMER_OUTPUT1_R
High level is reflected at the output compare1 pin after
successful comparison of output compare1 register with
free running counter.
TIMER_OUTPUT2_F
Low level is reflected at the output compare1 pin after suc-
cessfully capturing edge at ICAP1 pin.
TIMER_OUTPUT2_R
High level is reflected at the output compare1 pin after
successfully capturing edge at ICAP1 pin.
OCR _VALUE
You can select this value from 0x0000 to 0xFFFF.
None
1. ICAP1 pin used must be configured as floating input.
2. To get OPM active, PWM must be disabled.
None
1. Input capture1 flag is set.
2.Timer is active in One pulse mode and waveform can be
seen on OCMP1 pin.
3.Only Input capture 2 function can be used.
TIMERx_PWM_Mode
1)