ST7FLITE35F2M6 STMicroelectronics, ST7FLITE35F2M6 Datasheet - Page 108

• Manufacturer Part Number: ST7FLITE35F2M6
• Description: IC MCU 8BIT 8K FLASH 20SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE35F2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST7FLITE3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 7 Channel
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5085 - EVAL BOARD UNIV MOTOR CONTROL497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Function Descriptions
Table 64. I2C Slave Functions:
Notes:
– For ST72F63B device there is only one address register I2COAR (It does not support 10 bit
– If single master I2C device is selected, I2C will remain idle as in this case I2C can not behave
– When slave is in the interrupt mode. That is,
Caution:
– If ITE bit is forcibly modified in the User routine using the hardware register then the behav-
– If you are using the I2C as both transmitter and receiver, then both should be configured in
108/235
Function Name
Function Prototype
Behaviour Description
Input Parameter 1
Input Parameter 2
Input Parameter 3
Output Parameters
Required Preconditions
Functions called
Postconditions
See also
addressing). Here I2COAR will get the value of I2Cs_OAR1Value and the value of
I2Cs_OAR2Value will be neglected.
as slave.
if #ifdef I2C_ITDRV_WITHOUTBUF_TX
# ifdef I2C_ITDRV_WITHOUTBUF_RX are defined then ITE bit is also set in control register
automatically. There is no separate parameter for enabling the ITE bit.
iour of the I2C slave library is unpredictable.
the same mode (Polling/ Interrupt driven).
I2Cs_Init
Void I2Cs_Init(I2Cs_Control_Param InitParam,unsigned
char I2Cs_OAR1Value,unsigned char I2Cs_OAR2Value)
By default, Acknowledge and General Call are disabled.
You can change the default configuration by selecting in-
put parameters given below. You can pass one or more
parameters by logically ORing them. I2C peripheral is also
enabled.
I2Cs_DEFAULT_PARAM
Load I2C control registers with default value
I2Cs_ENABLE_ACK
Enables acknowledge.
I2Cs_ENABLE_ENGC
Enables General Call
I2Cs_OAR1Value
Load the OAR1 address.
I2Cs_OAR2Value
Load 10 bit higher address bits and also sets FRi bits ac-
cording to the value of Fcpu.
None
I/O port should be configured correctly.
None
None
None
Or,